- 您現在的位置：買賣IC網 > PDF目錄39192 > LC89052T SPECIALTY CONSUMER CIRCUIT, PDSO24 PDF資料下載
參數資料
| 型號： | LC89052T |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| 封裝： | 0.225 INCH, TSSOP-24 |
| 文件頁數： | 21/42頁 |
| 文件大小： | 482K |
| 代理商： | LC89052T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LC89052T
No.7457-28/42
9.2 CCB Addresses
Setting various functions, and reading and writing data must be carried out though the microcontroller interface.
The data through the microcontroller interface conforms to the Sanyo’s original serial bus format (CCB). However,
the three-state is employed instead of open-drain as the data output type.
Data must be input or output after the CCB address is input. See the I/O timing chart for details of the data input and
output timing.
Table 9.3 Register I/O Content and CCB Addresses
Register content
R/W
CCB address
B0
B1
B2
B3
A0
A1
A2
A3
Function settings data 1
Write
0xE8
0
1
0
1
Function settings data 2
Write
0xE9
1
0
1
0
1
Function settings data 3
Write
0xEA
0
1
0
1
0
1
Interrupt data output
Read
0xEB
1
0
1
0
1
Fs value, CS data output
Read
0xEC
0
1
0
1
Sub-code Q data output
Read
0xED
1
0
1
0
1
9.3 Data Write Procedure
The bit length of data input is 16 bits.
After inputting one of the CCB addresses data 0xE8 to 0xEA, set CE to the high level.
Input data is taken in on the rising edge of CL.
The bits marked "0" in the table are reserved bits. 0 (zero) must be input to these bits.
9.4 Data Read Procedure
Read data is output from DO. DO goes to the high-impedance state when CE is low, and output starts on the CE rising
edge that follows the output setup with the CCB address. After that, the DO pin is returned to the high-impedance
state when CE is set low.
The number of data bits read differs with the data to be read. Interrupt data (0xEB) is 8 bits long, the channel status
related data (0xEC) is 56 bits long, and the sub-code Q data (0xED) is 88 bits long. However, it is not necessary to
read out all data bits. During readout, an application can stop providing CL input and set CE low and still have
acquired the data read up to that point. For example, when reading the sub-code Q data, if the CRC flags are read and
the data is found no good, there is no need to read the subsequent data.
相關PDF資料 |
PDF描述 |
|---|---|
| LC89060M | PARALLEL, WORD INPUT LOADING, 6-BIT DAC, PDSO20 |
| LC89060 | PARALLEL, WORD INPUT LOADING, 6-BIT DAC, PDIP16 |
| LC89066 | 1-CH 6-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDIP16 |
| LC89066M | 1-CH 6-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDSO20 |
| LC89080 | TRIPLE, PARALLEL, 8 BITS INPUT LOADING, 8-BIT DAC, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC89052TA-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| LC89052TA-TLM-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| LC89052THS-E | 制造商:ON Semiconductor 功能描述:AUDIO I/F RECEIVER |
| LC890561W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Digital Audio Interface Receiver with Built-in Data Buffer Memory |
| LC890561W-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
發布緊急采購，3分鐘左右您將得到回復。