參數資料
型號： LIS202DL
廠商： 意法半導體
英文描述： MEMS motion sensor 2-axis - 【2g/【8g smart digital output “piccolo” accelerometer
中文描述： MEMS運動傳感器2軸- 【2克/【八克智能數字輸出的“小報”加速度
文件頁數： 15/36頁
文件大?。?/td> 249K
代理商： LIS202DL
LIS202DL
Digital interfaces
15/36
Figure 4.
Read & write protocol
CS
is the Serial Port Enable and it is controlled by the SPI master. It goes low at the start of
the transmission and goes back high at the end.
SPC
is the Serial Port Clock and it is
controlled by the SPI master. It is stopped high when
CS
is high (no transmission).
SDI
and
SDO
are respectively the Serial Port Data Input and Output. Those lines are driven at the
falling edge of
SPC
and should be captured at the rising edge of
SPC
.
Both the Read Register and Write Register commands are completed in 16 clock pulses or
in multiple of 8 in case of multiple byte read/write. Bit duration is the time between two falling
edges of
SPC
. The first bit (bit 0) starts at the first falling edge of
SPC
after the falling edge
of
CS
while the last bit (bit 15, bit 23, ...) starts at the last falling edge of SPC just before the
rising edge of
CS
.
bit 0
: RW bit. When 0, the data DI(7:0) is written into the device. When 1, the data DO(7:0)
from the device is read. In latter case, the chip will drive
SDO
at the start of bit 8.
bit 1
: MS bit. When 0, the address will remain unchanged in multiple read/write commands.
When 1, the address will be auto incremented in multiple read/write commands.
bit 2-7
: address AD(5:0). This is the address field of the indexed register.
bit 8-15
: data DI(7:0) (write mode). This is the data that will be written into the device (MSb
first).
bit 8-15
: data DO(7:0) (read mode). This is the data that will be read from the device (MSb
first).
In multiple read/write commands further blocks of 8 clock periods will be added. When MS
bit is 0 the address used to read/write data remains the same for every block. When MS bit
is 1 the address used to read/write data is incremented at every block.
The function and the behavior of
SDI
and
SDO
remain unchanged.
CS
SPC
SDI
SDO
RW
AD5 AD4 AD3 AD2 AD1 AD0
DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0
DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0
MS
相關PDF資料
PDF描述
LIS202DLTR MEMS motion sensor 2-axis - 【2g/【8g smart digital output “piccolo” accelerometer
LIS244AL MEMS motion sensor:2-axis - 【2g ultracompact linear accelerometer
LIS244ALTR MEMS motion sensor:2-axis - 【2g ultracompact linear accelerometer
LIS2L02AQ3 MEMS INERTIAL SENSOR: 2-axis - 【2g/【6g LINEAR ACCELEROMETER
LIS2L02AQ3TR MEMS INERTIAL SENSOR: 2-axis - 【2g/【6g LINEAR ACCELEROMETER
相關代理商/技術參數
參數描述
LIS202DLTR 功能描述:加速計 - 板上安裝 ULTRA COMPACT LOW POWER 2 AXES LIN A RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS244AL 功能描述:加速計 - 板上安裝 MEMS MOTION SENSOR 2-AXIS RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS244ALH 功能描述:加速計 - 板上安裝 MEMS Inertial High Pef 2-Axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS244ALHTR 功能描述:加速計 - 板上安裝 MEMS Inertial High Pef 2-Axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS244ALTR 功能描述:加速計 - 板上安裝 MEMS motion snsr 2 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*