- 您現在的位置：買賣IC網 > PDF目錄358821 > LM2576D2T-12 (MOTOROLA INC) EASY SWITCHERE⑩ 3.0 A STEP-DOWN VOLTAGE REGULATOR PDF資料下載
參數資料
| 型號： | LM2576D2T-12 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 穩壓器 |
| 英文描述： | EASY SWITCHERE⑩ 3.0 A STEP-DOWN VOLTAGE REGULATOR |
| 中文描述： | 3 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSSO5 |
| 封裝： | PLASTIC, D2PAK-5 |
| 文件頁數： | 16/26頁 |
| 文件大?。?/td> | 278K |
| 代理商： | LM2576D2T-12 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
LM2576
http://onsemi.com
16
Catch Diode
Locate the Catch Diode Close to the LM2576
The LM2576 is a stepdown buck converter; it requires a
fast diode to provide a return path for the inductor current
when the switch turns off. This diode must be located close
to the LM2576 using short leads and short printed circuit
traces to avoid EMI problems.
Use a Schottky or a Soft Switching
UltraFast Recovery Diode
Since the rectifier diodes are very significant sources of
losses within switching power supplies, choosing the
rectifier that best fits into the converter design is an
important process. Schottky diodes provide the best
performance because of their fast switching speed and low
forward voltage drop.
They provide the best efficiency especially in low output
voltage applications (5.0 V and lower). Another choice
could be FastRecovery, or UltraFast Recovery diodes. It
has to be noted, that some types of these diodes with an
abrupt turnoff characteristic may cause instability or
EMI troubles.
A fastrecovery diode with soft recovery characteristics
can better fulfill some quality, low noise design requirements.
Table 1 provides a list of suitable diodes for the LM2576
regulator. Standard 50/60 Hz rectifier diodes, such as the
1N4001 series or 1N5400 series are
NOT
suitable.
Inductor
The magnetic components are the cornerstone of all
switching power supply designs. The style of the core and
the winding technique used in the magnetic component’s
design has a great influence on the reliability of the overall
power supply.
Using an improper or poorly designed inductor can cause
high voltage spikes generated by the rate of transitions in
current within the switching power supply, and the
possibility of core saturation can arise during an abnormal
operational mode. Voltage spikes can cause the
semiconductors to enter avalanche breakdown and the part
can instantly fail if enough energy is applied. It can also
cause significant RFI (Radio Frequency Interference) and
EMI (ElectroMagnetic Interference) problems.
Continuous and Discontinuous Mode of Operation
The LM2576 stepdown converter can operate in both the
continuous and the discontinuous modes of operation. The
regulator works in the continuous mode when loads are
relatively heavy, the current flows through the inductor
continuously and never falls to zero. Under light load
conditions, the circuit will be forced to the discontinuous
mode when inductor current falls to zero for certain period
of time (see Figure 23 and Figure 24). Each mode has
distinctively different operating characteristics, which can
affect the regulator performance and requirements. In many
cases the preferred mode of operation is the continuous
mode. It offers greater output power, lower peak currents in
the switch, inductor and diode, and can have a lower output
ripple voltage. On the other hand it does require larger
inductor values to keep the inductor current flowing
continuously, especially at low output load currents and/or
high input voltages.
To simplify the inductor selection process, an inductor
selection guide for the LM2576 regulator was added to this
data sheet (Figures 18
through
22). This guide assumes that
the regulator is operating in the continuous mode, and
selects an inductor that will allow a peaktopeak inductor
ripple current to be a certain percentage of the maximum
design load current. This percentage is allowed to change as
different design load currents are selected. For light loads
(less than approximately 300 mA) it may be desirable to
operate the regulator in the discontinuous mode, because the
inductor value and size can be kept relatively low.
Consequently, the percentage of inductor peaktopeak
current increases. This discontinuous mode of operation is
perfectly acceptable for this type of switching converter.
Any buck regulator will be forced to enter discontinuous
mode if the load current is light enough.
HORIZONTAL TIME BASE: 5.0 s/DIV
Figure 23. Continuous Mode Switching Current
Waveforms
V
2.0 A
0 A
2.0 A
0 A
Inductor
Current
Waveform
Power
Switch
Current
Waveform
Selecting the Right Inductor Style
Some important considerations when selecting a core type
are core material, cost, the output power of the power supply,
the physical volume the inductor must fit within, and the
amount of EMI (ElectroMagnetic Interference) shielding
that the core must provide. The inductor selection guide
covers different styles of inductors, such as pot core, Ecore,
toroid and bobbin core, as well as different core materials
such as ferrites and powdered iron from different
manufacturers.
For high quality design regulators the toroid core seems to
be the best choice. Since the magnetic flux is contained
within the core, it generates less EMI, reducing noise
problems in sensitive circuits. The least expensive is the
bobbin core type, which consists of wire wound on a ferrite
rod core. This type of inductor generates more EMI due to
the fact that its core is open, and the magnetic flux is not
contained within the core.
相關PDF資料 |
PDF描述 |
|---|---|
| LM2576R | 3.0A, 15V, Step-Down Switching Regulator |
| LM2577S-12 | Pressure Transducer, Series 19 mm, Uncompensated, Pressure Range: 0 psi to 100 psi, Absolute, flush mount, 10 Vdc excitation |
| LM2577N-ADJ | Pressure Transducer, Series 19 mm, Compensated, Pressure Range: 0 psi to 200 psi, Absolute, flush mount with flange, 10 Vdc excitation |
| LM2577N-15 | Pressure Transducer, Series 19 mm, Compensated, Pressure Range: 0 psi to 200 psi, Absolute, flush mount, 10 Vdc excitation |
| LM2577N-12 | SIMPLE SWITCHER Step-Up Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2576D2T-15 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:EASY SWITCHERE⑩ 3.0 A STEP-DOWN VOLTAGE REGULATOR |
| LM2576D2T-15G | 功能描述:直流/直流開關調節器 15V 3A Buck PWM RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2576D2T-3.3 | 功能描述:直流/直流開關調節器 3.3V 3A Buck PWM RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2576D2T-3.3G | 功能描述:直流/直流開關調節器 3.3V 3A Buck PWM RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2576D2T-5 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Easy Switcher 3.0A Step-Down Voltage Regulator |
發布緊急采購，3分鐘左右您將得到回復。