參數資料
型號: LM3622MX-8.4
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 穩壓器
英文描述: Lithium-Ion Battery Charger Controller
中文描述: BATTERY CHARGE CONTROLLER, PDSO8
封裝: SOIC-8
文件頁數: 6/9頁
文件大?。?/td> 171K
代理商: LM3622MX-8.4
Functional Description
The simplified LM3622 block diagram in Figure 1 gives a
general idea of the circuit operation. The controller integrates
the reference, feedback and drive functions on-chip to con-
trol a linear, lithium-ion battery charger in constant voltage
and constant current (CVCC) charge operation. The regu-
lated output voltage is sensed between CEL and CS, and the
battery charge current is sensed across a current-sense re-
sistor between CS and GND. The EXT pin is designed for
driving a series pass element, which can be a PNP transistor
or a P-MOSFET.
Tying the LV
pin to ground enables the controller’s
low-voltage detection circuit. When the low-voltage detection
circuit is enabled and a battery voltage below a preset
threshold is detected, the LM3622 will drive the LV pin low
and shut off the current flowing into the EXT pin to suspend
the CVCC charge process. The low-voltage threshold is user
selectable to be either 2.15V/cell or 2.7V/cell by pulling the
LV
SEL
pin to GND or V
CC
respectively. The LV pin is a NPN
open collector output that can be used to turn on a low cur-
rent source to wake up charge a deeply depleted battery.
When the low-voltage detection is disabled (LV
pulled up
to V
), the LM3622 always starts the charge cycle in con-
stant current mode at any battery voltage below the control-
ler’s regulation level, and maintains the LV pin at a
high-impedance state.
Application Information
CEL Pin Current Drain
The LM3622 has an internal power down switch in series
with the on-chip resistor divider that is used for sensing the
battery voltage. In the event that the V
CC
supply is removed,
the power down switch will disconnect the resistor divider
from the CS pin, preventing the battery from discharging
through the CEL pin.
EXT Pin
The EXT pin is internally pulled up to V
via a 20μA current
source
making
it
possible
base-emitter resistor when driving a PNP transistor, or the
gate-source resistor when driving a P-MOSFET. However,
the voltage applied to EXT is not allowed to be higher than
(V
CC
+ 0.3V), otherwise the reverse current from EXT pin to
V
CC
pin may cause damage to the device.
to
eliminate
the
external
LV Pin Current Rating
The LV pin is a low power, NPN open collector output that is
rated to sink 10mAmaximum. Therefore, the value of the pull
up resistor should be chosen high enough to limit the current
to be less than 10mA.
CS Pin
In normal operation, the current limit threshold voltage for
the CS pin is 100mV typical. In case of a fault condition, the
voltage to this pin should be limited to below 5V.
DS100974-11
FIGURE 1. LM3622 Simplified Block Diagram
L
www.national.com
6
相關PDF資料
PDF描述
LM363H-500 LM363 Precision Instrumentation Amplifier
LM363D Instrumentation Amp, Fixed Gain
LM363H-10 LM363 Precision Instrumentation Amplifier
LM363H-100 LM363 Precision Instrumentation Amplifier
LM363 LM363 Precision Instrumentation Amplifier
相關代理商/技術參數
參數描述
LM36274EVM 功能描述:LM36274 4, Non-Isolated Output LED Driver Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 電流 - 輸出/通道:- 輸出和類型:4,非隔離 電壓 - 輸出:- 特性:- 電壓 - 輸入:2.7 V ~ 5 V 所含物品:板 使用的 IC/零件:LM36274 標準包裝:1
LM363 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM363 Precision Instrumentation Amplifier
LM3630A 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM3630A High-Efficiency Dual-String White LED Driver
LM3630ATME 制造商:Texas Instruments 功能描述:LED DRVR 20Segment 2.5V/3.3V/5V 12-Pin DSBGA T/R 制造商:Texas Instruments 功能描述:IC LED DRIVER 2-STRING 12DSBGA 制造商:Texas Instruments 功能描述:Hi Eff Dual-String White LED Dvr
LM3630ATMX 制造商:Texas Instruments 功能描述:IC LED DRIVER 2-STRING 12DSBGA 制造商:Texas Instruments 功能描述:LED BACKLIGHT DRIVER 制造商:Texas Instruments 功能描述:LINEAR IC