- 您現在的位置：買賣IC網 > PDF目錄358861 > LM40 (National Semiconductor Corporation) Hardware Monitor with Dual Thermal Diodes and SensorPath Bus PDF資料下載
參數資料
| 型號： | LM40 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Hardware Monitor with Dual Thermal Diodes and SensorPath Bus |
| 中文描述： | 硬件監控雙熱二極管和SensorPath總線 |
| 文件頁數： | 12/27頁 |
| 文件大?。?/td> | 369K |
| 代理商： | LM40 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
1.0 Functional Description
(Continued)
1.3.2 Read Transaction
During a read transaction, the master reads data from a
register at a specified address within a slave. A read trans-
action begins with a Start Bit and ends with an ACK bit, as
shown in
Figure 5
.
Device Number
This is the address of the LM40 device
accessed. Address "000" is a broadcast address and can
be responded to by all the slave devices. The LM40
ignores the broadcast address during a read transaction.
Internal Address
The address of a register within the
LM40 that is read.
Read/Write (R/W)
A "1" indicates a read transaction.
Data Bits
During a read transaction the data bits are
driven by the LM40. Data is transferred serially with the
most significant bit first. This allows throughput optimiza-
tion based on the information that needs to be read.
The LM40 supports 8-bit or 16-bit data fields, as de-
scribed in
Section 2.0
"Register Set".
Even Parity (EP)
This bit is based on all preceding bits
(device number, internal address, Read/Write and data
bits) and the parity bit itself. The parity -number of 1’s - of
all the preceding bits and the parity bit must be even - i.e.,
the result must be 0. During a read transaction, the EP bit
is sent by the LM40 to the master to allow the master to
check the received data before using it.
Acknowledge (ACK)
During a read transaction theACK
bit is sent by the master indicating that the EP bit was
received and was found to be correct, when compared to
the data preceding it, and that no conflict was detected
on the bus (excluding Attention Request - see
Section
1.3.5
"Attention Request Transaction"). A read transfer is
considered "complete" only when theACK bit is received.
A transaction that was not positively acknowledged is not
considered "complete" by the LM40 and following are
performed:
— The BER bit in the LM40 Device Status register is set
— The LM40 generates an Attention Request before, or
together with the Start Bit of the next transaction
A transaction that was not positively acknowledged is
also not considered "complete" by the master (i.e. inter-
nal operations related to the transaction are not per-
formed). The transaction may be repeated by the master,
after detecting the source of the Attention Request (the
LM40 that has a set BER bit in the Device Status regis-
ter). Note that the SensorPath protocol neither forces, nor
automates re-execution of the transaction by the master.
The values of the ACK bit are:
— 1: Data was received correctly
— 0: An error was detected (no-acknowledge).
1.3.3 Write Transaction
In a write transaction, the master writes data to a register at
a specified address in the LM40. A write transaction begins
with a Start Bit and ends with an ACK Data Bit, as show in
Figure 6
.
Device Number
This is the address of the slave device
accessed. Address "000" is a broadcast address and is
responded to by all the slave devices. The LM40 re-
sponds to broadcast messages to the Device Control
Register.
Internal Address
This is the register address in the
LM40 that will be written.
Read/Write (R/W)
A "0" data bit directs a write transac-
tion.
20068408
FIGURE 4. Bus Reset Transaction
20068409
FIGURE 5. Read Transaction, master reads data from LM40
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM4120AIM5X-5.0 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5-1.8 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5-3.3 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5X-2.5 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5X-3.3 | Precision Micropower Low Dropout Voltage Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM400 | 制造商:LM TECHNOLOGIES 功能描述:MODULE BLUETOOTH V2.0 CLASS 1 BC04 制造商:LM TECHNOLOGIES 功能描述:BLUETOOTH MODULE, BC04, CLASS 1, EDR 制造商:LM TECHNOLOGIES 功能描述:BLUETOOTH MOD, PDA, GPS, POS, BC04, CLASS 1, EDR; Supply Voltage Min:2.7V; Supply Voltage Max:3.6V; Data Rate:3Mbps; Bluetooth Version:Bluetooth 2.0 + EDR; Bluetooth Class:Class 1; Receive Sensitivity:-88dBm; Type:Bluetooth Module ;RoHS Compliant: Yes |
| LM4001 | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT SILICON RECTIFIERS |
| LM4001G | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIERS |
| LM4002 | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT SILICON RECTIFIERS |
| LM4002G | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIERS |
發布緊急采購，3分鐘左右您將得到回復。