- 您現在的位置：買賣IC網 > PDF目錄358861 > LM40 (National Semiconductor Corporation) Hardware Monitor with Dual Thermal Diodes and SensorPath Bus PDF資料下載
參數資料
| 型號： | LM40 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Hardware Monitor with Dual Thermal Diodes and SensorPath Bus |
| 中文描述： | 硬件監控雙熱二極管和SensorPath總線 |
| 文件頁數： | 26/27頁 |
| 文件大?。?/td> | 369K |
| 代理商： | LM40 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁
3.0 Application Hints
(Continued)
3.
Ideally, the LM40 should be placed within 10cm of the
Processor diode pins with the traces being as straight,
short and identical as possible. Trace resistance of 0.7
can cause as much as 1C of error. This error can be
compensated for by adding or subtracting an offset to
the remote temperature reading(s).
Diode traces should be surrounded by a GND guard ring
to either side, above and below if possible. This GND
guard should not be between the D+ and D lines. In the
event that noise does couple to the diode lines it would
be ideal if it is coupled common mode. That is equally to
the D+ and D lines.
Avoid routing diode traces in close proximity to power
supply switching or filtering inductors.
Avoid running diode traces close to or parallel to high
speed digital and bus lines. Diode traces should be kept
at least 2cm apart from the high speed digital traces.
If it is necessary to cross high speed digital traces, the
diode traces and the high speed digital traces should
cross at a 90 degree angle.
4.
5.
6.
7.
8.
The ideal place to connect the LM40’s GND pin is as
close as possible to the Processors GND associated
with the sense diode.
Leakage current between D+ and GND should be kept
to a minimum. Seventeen nano-amperes of leakage can
cause as much as 0.2C of error in the diode tempera-
ture reading (see curve in
Section Typical Performance
Characteristics
). Keeping the printed circuit board as
clean as possible will minimize leakage current.
The SensorPath Bus is less sensitive to noise than its pre-
decessor the SMBus due to the inherent filtering present in
the pulse-width encoding of the data. Care still needs to be
taken such that induced noise is analyzed and minimized.
SensorPath Bus corrupt data is the most common symptom
for noise coupled in SWD. A no-ACK is the symptom for
noise coupled into the Device Number Select pin (ADD). An
RC lowpass filter as well as a debouncing circuit are in-
cluded in the LM40 that filter noise spikes less than 2.5 μsec
in duration on the SWD signal.
9.
L
www.national.com
26
相關PDF資料 |
PDF描述 |
|---|---|
| LM4120AIM5X-5.0 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5-1.8 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5-3.3 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5X-2.5 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5X-3.3 | Precision Micropower Low Dropout Voltage Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM400 | 制造商:LM TECHNOLOGIES 功能描述:MODULE BLUETOOTH V2.0 CLASS 1 BC04 制造商:LM TECHNOLOGIES 功能描述:BLUETOOTH MODULE, BC04, CLASS 1, EDR 制造商:LM TECHNOLOGIES 功能描述:BLUETOOTH MOD, PDA, GPS, POS, BC04, CLASS 1, EDR; Supply Voltage Min:2.7V; Supply Voltage Max:3.6V; Data Rate:3Mbps; Bluetooth Version:Bluetooth 2.0 + EDR; Bluetooth Class:Class 1; Receive Sensitivity:-88dBm; Type:Bluetooth Module ;RoHS Compliant: Yes |
| LM4001 | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT SILICON RECTIFIERS |
| LM4001G | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIERS |
| LM4002 | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT SILICON RECTIFIERS |
| LM4002G | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIERS |
發布緊急采購，3分鐘左右您將得到回復。