- 您現在的位置：買賣IC網 > PDF目錄30753 > LM4854LD/NOPB (NATIONAL SEMICONDUCTOR CORP) 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 PDF資料下載
參數資料
| 型號： | LM4854LD/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| 封裝： | LLP-14 |
| 文件頁數： | 11/29頁 |
| 文件大?。?/td> | 1440K |
| 代理商： | LM4854LD/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Application Information (Continued)
the amplifier that drives the headphone jack’s sleeve. If this
current exceeds 500mA
PK, the amplifier is shutdown, pro-
tecting the LM4854 and the external equipment. For more
information, see the section titled ’Single-Ended Output
Power Performance and Measurement Considerations’.
EXPOSED-DAP MOUNTING CONSIDERATIONS
The LM4854’s exposed-DAP (die attach paddle) package
(LD) provides a low thermal resistance between the die and
the PCB to which the part is mounted and soldered. This
allows rapid heat transfer from the die to the surrounding
PCB copper area heatsink, copper traces, ground plane, and
finally, surrounding air. The result is a low voltage audio
power amplifier that produces 1.7W dissipation in a 4
load
at
≤ 1% THD+N and over 1.9W in a 3 load at 10% THD+N.
This high power is achieved through careful consideration of
necessary thermal design. Failing to optimize thermal design
may compromise the LM4854’s high power performance and
activate unwanted, though necessary, thermal shutdown
protection.
The LD package must have its DAP soldered to a copper
pad on the PCB. The DAP’s PCB copper pad is then, ideally,
connected to a large plane of continuous unbroken copper.
This plane forms a thermal mass, heat sink, and radiation
area. Place the heat sink area on either outside plane in the
case of a two-sided or multi-layer PCB. (The heat sink area
can also be placed on an inner layer of a multi-layer board.
The thermal resistance, however, will be higher.) Connect
the DAP copper pad to the inner layer or backside copper
heat sink area with 6 (3 X 2) (LD) vias. The via diameter
should be 0.012in - 0.013in with a 1.27mm pitch. Ensure
efficient thermal conductivity by plugging and tenting the vias
with plating and solder mask, respectively.
Best thermal performance is achieved with the largest prac-
tical copper heat sink area. If the heatsink and amplifier
share the same PCB layer, a nominal 2.5in
2 (min) area is
necessary for 5V operation with a 4
load. Heatsink areas
not placed on the same PCB layer as the LM4854 should be
5in
2 (min) for the same supply voltage and load resistance.
The last two area recommendations apply for 25C ambient
temperature. Increase the area to compensate for ambient
temperatures above 25C. In all circumstances and under all
conditions, the junction temperature must be held below
150C to prevent activating the LM4854’s thermal shutdown
protection. The LM4854’s power de-rating curve in the Typi-
cal Performance Characteristics shows the maximum
power dissipation versus temperature. Example PCB layouts
for the exposed-DAP TSSOP and LD packages are shown in
the Demonstration Board Layout section. Further detailed
and specific information concerning PCB layout and fabrica-
tion and mounting an LD (LLP) is found in National Semi-
conductor’s AN1187.
20038207
FIGURE 2. Typical Audio Amplifier Application Circuit
LM4854
www.national.com
19
相關PDF資料 |
PDF描述 |
|---|---|
| LM4854LDX/NOPB | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LM4856LQ/NOPB | 1.5 W, 3 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| LM4856ITL/NOPB | 1.1 W, 3 CHANNEL, AUDIO AMPLIFIER, PBGA18 |
| LM4857GR/NOPB | SPECIALTY CONSUMER CIRCUIT, PBGA49 |
| LM4858MM/NOPB | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4854MM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AUDIO AMPLIFIER|DUAL|TSSOP|10PIN|PLASTIC |
| LM4854MT | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM4854MT/NOPB | 功能描述:IC AMP AUDIO PWR 2.3W AB 14TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4854MTX/NOPB | 功能描述:IC AMP AUDIO PWR 2.3W AB 14TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4855 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Boomer AUDIO POWER AMPLIFIER Integrated Audio Amplifier System |
發布緊急采購，3分鐘左右您將得到回復。