參數資料
型號： LM4854LD/NOPB
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 音頻／視頻放大
英文描述： 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14
封裝： LLP-14
文件頁數： 13/29頁
文件大小： 1440K
代理商： LM4854LD/NOPB
Application Information (Continued)
PCB LAYOUT AND SUPPLY REGULATION
CONSIDERATIONS FOR DRIVING 3
AND 4 LOADS
Power dissipated by a load is a function of the voltage swing
across the load and the load’s impedance. As load imped-
ance decreases, load dissipation becomes increasingly de-
pendent on the interconnect (PCB trace and wire) resistance
between the amplifier output pins and the load’s connec-
tions. Residual trace resistance causes a voltage drop,
which results in power dissipated in the trace and not in the
load as desired. For example, 0.1
trace resistance reduces
the output power dissipated by a 4
load from 1.7W to 1.6W.
The problem of decreased load dissipation is exacerbated
as load impedance decreases. Therefore, to maintain the
highest load dissipation and widest output voltage swing,
PCB traces that connect the output pins to a load must be as
wide as possible.
Poor power supply regulation adversely affects maximum
output power. A poorly regulated supply’s output voltage
decreases with increasing load current. Reduced supply
voltage causes decreased headroom, output signal clipping,
and reduced output power. Even with tightly regulated sup-
plies, trace resistance creates the same effects as poor
supply regulation. Therefore, making the power supply
traces as wide as possible helps maintain full output voltage
swing.
BRIDGE CONFIGURATION EXPLANATION
As shown in Figure 2, the LM4854 consists of three opera-
tional amplifiers. In mono mode, AMP1 and AMP2 operate in
series to drive a speaker connected between their outputs.
In stereo mode, AMP1 and AMP3 are used to drive stereo
headphones or other SE load.
In mono mode, external resistors R
fL and RiL set the closed-
loop gain of AMP1, whereas two internal 20k
resistors set
AMP2’s gain at -1. The LM4854 drives a load, such as a
speaker, connected between the two amplifier outputs,
L-OUT and BTL-OUT.
Figure 2 shows that AMP1’s output serves as AMP2’s input.
This results in both amplifiers producing signals identical in
magnitude, but 180 out of phase. Taking advantage of this
phase difference, a load is placed between L-OUT and BTL-
OUT and driven differentially (commonly referred to as
"bridge mode"). This results in a differential,or BTL, gain of:
A
VD = 2(Rf/Ri)
(1)
Bridge mode amplifiers are different from single-ended am-
plifiers that drive loads connected between a single amplifi-
er’s output and ground. For a given supply voltage, bridge
mode has a distinct advantage over the single-ended con-
figuration: its differential output doubles the voltage swing
across the load. Theoretically, this produces four times the
output power when compared to a single-ended amplifier
under the same conditions. This increase in attainable output
power assumes that the amplifier is not current limited and
that the output signal is not clipped. To ensure minimum
output signal clipping when choosing an amplifier’s closed-
loop gain, refer to the Audio Power Amplifier Design section.
Another advantage of the differential bridge output is no net
DC voltage across the load. This is accomplished by biasing
AMP1’s and AMP2’s outputs at half-supply. This eliminates
the coupling capacitor that single supply, single-ended am-
plifiers require. Eliminating an output coupling capacitor in a
typical single-ended configuration forces a single-supply am-
plifier’s half-supply bias voltage across the load. This in-
creases internal IC power dissipation and may permanently
damage loads such as speakers.
POWER DISSIPATION
Power dissipation is a major concern when designing a
successful single-ended or bridged amplifier. Equation (2)
states the maximum power dissipation point for a single-
ended amplifier operating at a given supply voltage and
driving a specified output load.
P
DMAX-SE =(VDD)
2/(2
π2 R
L): Single-Ended
(2)
However, a direct consequence of the increased power de-
livered to the load by a bridge amplifier is higher internal
power dissipation for the same conditions. The LM4854 has
two operational amplifiers driving a mono bridge load. The
maximum internal power dissipation operating in the bridge
mode is twice that of a single-ended amplifier. From Equa-
tion (3), assuming a 5V power supply and an 8
load, the
maximum BTL-mode power dissipation is 317mW.
P
DMAX-MONOBTL = 4(VDD)
2/(2
π2 R
L): Bridge Mode
(3)
The maximum power dissipation point given by Equation (3)
must not exceed the power dissipation given by Equation
(4):
P
DMAX’= (TJMAX -TA)/
θ
JA
(4)
The LM4854’s TJMAX = 150C. In the IBL package, the
LM4854’s
θ
JA is 121C/W. The LM4854’s TJMAX = 150C. In
the LD package soldered to a DAP pad that expands to a
copper area of 2.0in
2 on a PCB, the LM4854’s
θ
JA is 42C/W.
In the MT package, the LM4854’s
θ
JA is 109C/W. At any
given ambient temperature T
A, use Equation (4) to find the
maximum internal power dissipation supported by the IC
packaging. Rearranging Equation (4) and substituting P
DMAX
for P
DMAX’ results in Equation (5). This equation gives the
maximum ambient temperature that still allows maximum
stereo power dissipation without violating the LM4854’s
maximum junction temperature.
T
A =TJMAX -PDMAX-MONOBTL
θ
JA
(5)
For a typical application with a 5V power supply and an 8
load, the maximum ambient temperature that allows maxi-
mum stereo power dissipation without exceeding the maxi-
mum junction temperature is approximately 73C for the IBL
package.
T
JMAX =PDMAX-MONOBTL
θ
JA +TA
(6)
Equation (6) gives the maximum junction temperature T
J-
MAX
. If the result violates the LM4854’s 150C, reduce the
maximum junction temperature by reducing the power sup-
ply voltage or increasing the load resistance. Further allow-
ance should be made for increased ambient temperatures.
The above examples assume that a device is a surface
mount part operating around the maximum power dissipation
point. Since internal power dissipation is a function of output
LM4854
www.national.com
20
相關PDF資料
PDF描述
LM4854LDX/NOPB 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14
LM4856LQ/NOPB 1.5 W, 3 CHANNEL, AUDIO AMPLIFIER, QCC24
LM4856ITL/NOPB 1.1 W, 3 CHANNEL, AUDIO AMPLIFIER, PBGA18
LM4857GR/NOPB SPECIALTY CONSUMER CIRCUIT, PBGA49
LM4858MM/NOPB 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10
相關代理商/技術參數
參數描述
LM4854MM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AUDIO AMPLIFIER|DUAL|TSSOP|10PIN|PLASTIC
LM4854MT 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:
LM4854MT/NOPB 功能描述:IC AMP AUDIO PWR 2.3W AB 14TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
LM4854MTX/NOPB 功能描述:IC AMP AUDIO PWR 2.3W AB 14TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
LM4855 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Boomer AUDIO POWER AMPLIFIER Integrated Audio Amplifier System
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*