- 您現在的位置：買賣IC網 > PDF目錄361034 > LM81 (National Semiconductor Corporation) Serial Interface ACPI-Compatible Microprocessor System PDF資料下載
參數資料
| 型號： | LM81 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Serial Interface ACPI-Compatible Microprocessor System |
| 中文描述： | 串行接口ACPI的兼容微處理器系統 |
| 文件頁數： | 12/32頁 |
| 文件大小： | 412K |
| 代理商： | LM81 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Functional Description
(Continued)
2.2 Serial Bus Interface
The Serial Bus control lines consist of the SMBData (serial
data), SMBCLK (serial clock) and A0-A1 (address) pins. The
LM81 can operate only as a slave. The SMBCLK line only
controls the serial interface, all other clock functions within
LM81 such as the ADC and fan counters are done with a
separate asynchronous internal clock.
When using the Serial Bus Interface a write will always con-
sist of the LM81 Serial Bus Interface Address byte, followed
by the Internal Address Register byte, then the data byte.
There are two cases for a read:
1.
If the InternalAddress Register is known to already be at
the desired Address, simply read the LM81 with the Se-
rial Bus Interface Address byte, followed by the data
byte read from the LM81.
2.
If the Internal Address Register value is unknown, or if it
is not the desired value, write to the LM81 with the Serial
Bus Interface Address byte, followed by the Internal Ad-
dress Register byte. Then restart the Serial Communica-
tion with a Read consisting of the Serial Bus Interface
Address byte, followed by the data byte read from the
LM81.
The default Serial Bus address of the LM81 is set to 010
11(A1)(A0).All bits, except forA0 andA1, can be changed by
writing to the Serial Bus address register. A0 and A1 will al-
ways reflect the state of the A0 and A1 input pins.
All of these communications are depicted in the Serial Bus
Interface Timing Diagrams as shown in Figure 5
Serial Bus Timeout can be initiated by holding the SMBCLK
and/or SMBData lines low for greater than t
(35 ms
max). Serial Bus Timeout resets the serial bus interface cir-
cuitry to the idle state and readies the LM81 for a new serial
bus communication.
DS100072-8
(a) Serial Bus Write to the Internal Address Register followed by the Data Byte
DS100072-9
(b) Serial Bus Write to the Internal Address Register Only
DS100072-10
(c) Serial Bus Read from a Register with the Internal Address Register Preset to Desired Location
FIGURE 5. Serial Bus Timing
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM81CIMT-31 | Serial Interface ACPI-Compatible Microprocessor System |
| LM82CIMQAX | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM82CIMQA | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM82 | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM8300HVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8-1 | 制造商:Banner Engineering 功能描述:Logic Module; Delayed One-Shot; ,Ranges For Banner Multi-Beam Sensor Blocks 制造商:Banner Engineering 功能描述:3-And 4-Wire Logic Modules |
| LM81_02 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM810 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:3-Pin Microprocessor Reset Circuits |
| LM810A-2.63 E WAF | 制造商:Texas Instruments 功能描述: |
| LM810A-2.93 E WAF | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。