- 您現在的位置：買賣IC網 > PDF目錄361034 > LM81 (National Semiconductor Corporation) Serial Interface ACPI-Compatible Microprocessor System PDF資料下載
參數資料
| 型號： | LM81 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Serial Interface ACPI-Compatible Microprocessor System |
| 中文描述： | 串行接口ACPI的兼容微處理器系統 |
| 文件頁數： | 19/32頁 |
| 文件大小： | 412K |
| 代理商： | LM81 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Functional Description
(Continued)
8.2 Temperature Interrupts
INT and T_CRIT_A outputs are provided for temperature in-
terrupt. Temperature interrupts have a normal and an ex-
tended option of operation. Each option has three different
modes of operation: Repetitive Interrupt, One-Time Interrupt
and Comparator.
Normal Repetitive Interrupt Mode
is shown in Figure 11
and operates in the following way: T_CRIT_A is disabled.
Exceeding T
causes an interrupt that will remain active
indefinitely until reset by reading Interrupt Status Register 1.
Once reset if the temperature remains above the T
setpoint the interrupt will again be activated at the comple-
tion of another conversion cycle. If temperature is less than
or equal to T
HIHYST
the interrupt will not be activated.
Normal One-Time Interrupt Mode
is shown in Figure 12
and operates in the following way: T_CRIT_A is disabled.
Exceeding T
causes an interrupt that will remain active
indefinitely until reset by reading Interrupt Status Register 1.
Another interrupt will not occur until the temperature drops to
less than or equal to T
and then exceeds T
during
a subsequent conversion. After power up this mode is se-
lected as default.
Normal Comparator Mode
is shown in Figure 13 and oper-
ates in the following way: T_CRIT_A is disabled. Exceeding
T
causes an interrupt that will remain activated until the
temperature is less than or equal to T
HIGH
. T
LOW
is disabled.
DS100072-16
*
Note:
Interrupt resets occur only when interrupt Status Register 1 is read.
FIGURE 11. Normal Repetitive Interrupt Response
Diagram
DS100072-17
*
Note:
Interrupt resets occur only when interrupt Status Register 1 is read.
FIGURE 12. One-Time Interrupt Response Diagram
DS100072-18
*
Note:
Interrupt resets occur only when interrupt Status Register 1 is read.
FIGURE 13. Normal Comparator Mode
www.national.com
19
相關PDF資料 |
PDF描述 |
|---|---|
| LM81CIMT-31 | Serial Interface ACPI-Compatible Microprocessor System |
| LM82CIMQAX | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM82CIMQA | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM82 | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM8300HVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8-1 | 制造商:Banner Engineering 功能描述:Logic Module; Delayed One-Shot; ,Ranges For Banner Multi-Beam Sensor Blocks 制造商:Banner Engineering 功能描述:3-And 4-Wire Logic Modules |
| LM81_02 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM810 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:3-Pin Microprocessor Reset Circuits |
| LM810A-2.63 E WAF | 制造商:Texas Instruments 功能描述: |
| LM810A-2.93 E WAF | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。