參數資料
型號: LPC2194JBD64
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: Single-chip 16/32-bit microcontrollers 256 kB ISP/IAP Flash with 10-bit ADC and CAN
中文描述: 32-BIT, FLASH, 60 MHz, RISC MICROCONTROLLER, PQFP64
封裝: 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64
文件頁數: 12/33頁
文件大小: 158K
代理商: LPC2194JBD64
Philips Semiconductors
LPC2194
Single-chip 16/32-bit microcontrollers
Preliminary data
Rev. 01 — 06 February 2004
12 of 33
9397 750 12757
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
6.6 Pin connect block
The pin connect block allows selected pins of the microcontroller to have more than
one function. Configuration registers control the multiplexers to allow connection
between the pin and the on chip peripherals. Peripherals should be connected to the
appropriate pins prior to being activated, and prior to any related interrupt(s) being
enabled. Activity of any enabled peripheral function that is not mapped to a related
pin should be considered undefined.
The Pin Control Module contains three registers as shown in
Table 5
.
6.7 Pin function select register 0 (PINSEL0 - 0xE002C000)
The PINSEL0 register controls the functions of the pins as per the settings listed in
Table 6
. The direction control bit in the IODIR register is effective only when the GPIO
function is selected for a pin. For other functions, direction is controlled automatically.
Settings other than those shown in
Table 6
are reserved, and should not be used
I
2
C
SPI0
SPI1
PLL
RTC
System Control
SI (state change)
SPIF, MODF
SPIF, MODF
PLL Lock (PLOCK)
RTCCIF (Counter Increment), RTCALF (Alarm)
External Interrupt 0 (EINT0)
External Interrupt 1 (EINT1)
External Interrupt 2 (EINT2)
External Interrupt 3 (EINT3)
A/D Converter
1 ORed CAN Acceptance Filter
CAN1 (Tx int, Rx int)
CAN2 (Tx int, Rx int)
CAN3 (Tx int, Rx int)
CAN4 (Tx int, Rx int)
9
10
11
12
13
14
15
16
17
18
19
20,21
22,23
24,25
26,27
A/D
CAN
Table 4:
Block
Interrupt sources
…continued
Flag(s)
VIC channel #
Table 5:
Address
0xE002C000
0xE002C004
0xE002C014
Name
PINSEL0
PINSEL1
PINSEL2
Description
Pin function select register 0
Pin function select register 1
Pin function select register 2
Access
Read/Write
Read/Write
Read/Write
Table 6:
PINSEL0
1:0
Pin function select register 0 (PINSEL0 - 0xE002C000)
Pin name
Value
P0.0
0
0
0
1
1
0
1
1
Function
GPIO Port 0.0
TxD (UART0)
PWM1
Reserved
Value after Reset
0
相關PDF資料
PDF描述
LPC2210 16/32-bit ARM microcontroller with 10-bit ADC and external memory interface
LPC2290 16/32-bit ARM microcontrollers with CAN, 10-bit ADC and external memory interface
LPC2292 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface
LPC2294JBD144 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface
LPC2294 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface
相關代理商/技術參數
參數描述
LPC2194JBD64,151 功能描述:ARM微控制器 - MCU 256K FL/16K RAM/4 CAN/10B ADC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2210 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontrollers; flashless with 64 kB, with 10-bit ADC and external memory interface
LPC2210_08 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontrollers; flashless, with 10-bit ADC and external memory interface
LPC2210FBD144 制造商:NXP Semiconductors 功能描述:
LPC2210FBD144,551 功能描述:ARM微控制器 - MCU RLESS/16K RAM/10B ADC/EXT BUS RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT