- 您現在的位置：買賣IC網 > PDF目錄367584 > LPC2194JBD64 (NXP SEMICONDUCTORS) Single-chip 16/32-bit microcontrollers 256 kB ISP/IAP Flash with 10-bit ADC and CAN PDF資料下載
參數資料
| 型號： | LPC2194JBD64 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single-chip 16/32-bit microcontrollers 256 kB ISP/IAP Flash with 10-bit ADC and CAN |
| 中文描述： | 32-BIT, FLASH, 60 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 23/33頁 |
| 文件大?。?/td> | 158K |
| 代理商： | LPC2194JBD64 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
Philips Semiconductors
LPC2194
Single-chip 16/32-bit microcontrollers
Preliminary data
Rev. 01 — 06 February 2004
23 of 33
9397 750 12757
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
fourth of the processor clock rate. The default condition at reset is for the VPB bus to
run at one quarter of the CPU clock. The second purpose of the VPB Divider is to
allow power savings when an application does not require any peripherals to run at
the full processor rate. Because the VPB Divider is connected to the PLL output, the
PLL remains active (if it was running) during Idle mode.
6.21 Emulation and debugging
The LPC2194 supports emulation and debugging via a JTAG serial port. A trace port
allows tracing program execution. Debugging and trace functions are multiplexed only
with GPIOs on Port 1. This means that all communication, timer and interface
peripherals residing on Port 0 are available during the development and debugging
phase as they are when the application is run in the embedded system itself.
6.21.1
Embedded ICE
Standard ARM EmbeddedICE logic provides on-chip debug support. The debugging
of the target system requires a host computer running the debugger software and an
EmbeddedICE protocol convertor. EmbeddedICE protocol convertor converts the
Remote Debug Protocol commands to the JTAG data needed to access the ARM
core.
The ARM core has a Debug Communication Channel function built-in. The debug
communication channel allows a program running on the target to communicate with
the host debugger or another separate host without stopping the program flow or
even entering the debug state. The debug communication channel is accessed as a
co-processor 14 by the program running on the ARM7TDMI-S core. The debug
communication channel allows the JTAG port to be used for sending and receiving
data without affecting the normal program flow. The debug communication channel
data and control registers are mapped in to addresses in the EmbeddedICE logic.
6.21.2
Embedded trace
Since the LPC2194 has significant amounts of on-chip memory, it is not possible to
determine how the processor core is operating simply by observing the external pins.
The Embedded Trace Macrocell provides real-time trace capability for deeply
embedded processor cores. It outputs information about processor execution to the
trace port.
The ETM is connected directly to the ARM core and not to the main AMBA system
bus. It compresses the trace information and exports it through a narrow trace port.
An external trace port analyzer must capture the trace information under software
debugger control. Instruction trace (or PC trace) shows the flow of execution of the
processor and provides a list of all the instructions that were executed. Instruction
trace is significantly compressed by only broadcasting branch addresses as well as a
set of status signals that indicate the pipeline status on a cycle by cycle basis. Trace
information generation can be controlled by selecting the trigger resource. Trigger
resources include address comparators, counters and sequencers. Since trace
information is compressed the software debugger requires a static image of the code
being executed. Self-modifying code can not be traced because of this restriction.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2210 | 16/32-bit ARM microcontroller with 10-bit ADC and external memory interface |
| LPC2290 | 16/32-bit ARM microcontrollers with CAN, 10-bit ADC and external memory interface |
| LPC2292 | 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface |
| LPC2294JBD144 | 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface |
| LPC2294 | 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2194JBD64,151 | 功能描述:ARM微控制器 - MCU 256K FL/16K RAM/4 CAN/10B ADC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2210 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontrollers; flashless with 64 kB, with 10-bit ADC and external memory interface |
| LPC2210_08 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontrollers; flashless, with 10-bit ADC and external memory interface |
| LPC2210FBD144 | 制造商:NXP Semiconductors 功能描述: |
| LPC2210FBD144,551 | 功能描述:ARM微控制器 - MCU RLESS/16K RAM/10B ADC/EXT BUS RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。