參數資料
型號: LPC2378FBD144
廠商: NXP Semiconductors N.V.
元件分類: 數學處理器
英文描述: Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC
封裝: LPC2377FBD144<SOT486-1 (LQFP144)|<<http://www.nxp.com/packages/SOT486-1.html<1<Always Pb-free,;LPC2378FBD144<SOT486-1 (LQFP144)|<<http://www.nxp.com/packages/SOT486-1.htm
文件頁數: 25/68頁
文件大?。?/td> 1443K
代理商: LPC2378FBD144
LPC2377_78
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 5 — 17 June 2010
25 of 68
NXP Semiconductors
LPC2377/78
Single-chip 16-bit/32-bit microcontrollers
7.14 10-bit DAC
The DAC allows the LPC2377/78 to generate a variable analog output. The maximum
output value of the DAC is V
i(VREF)
.
7.14.1
Features
10-bit DAC
Resistor string architecture
Buffered output
Power-down mode
Selectable output drive
7.15 UARTs
The LPC2377/78 contain four UARTs. In addition to standard transmit and receive data
lines, UART1 also provides a full modem control handshake interface.
The UARTs include a fractional baud rate generator. Standard baud rates such as 115200
can be achieved with any crystal frequency above 2 MHz.
7.15.1
Features
16 B Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
Fractional divider for baud rate control, auto baud capabilities and FIFO control
mechanism that enables software flow control implementation.
UART1 equipped with standard modem interface signals. This module also provides
full support for hardware flow control (auto-CTS/RTS).
UART3 includes an IrDA mode to support infrared communication.
7.16 SPI serial I/O controller
The LPC2377/78 contain one SPI controller. SPI is a full duplex serial interface designed
to handle multiple masters and slaves connected to a given bus. Only a single master and
a single slave can communicate on the interface during a given data transfer. During a
data transfer the master always sends 8 bits to 16 bits of data to the slave, and the slave
always sends 8 bits to 16 bits of data to the master.
7.16.1
Features
Compliant with SPI specification
Synchronous, Serial, Full Duplex Communication
Combined SPI master and slave
Maximum data bit rate of one eighth of the input clock rate
8 bits to 16 bits per transfer
相關PDF資料
PDF描述
LPC2387FBD100 Single-chip 16-bit-32-bit MCU; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2388FBD144 Single-chip 16-bit-32-bit micro; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2420FBD208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
LPC2420FET208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
LPC2460FBD208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
相關代理商/技術參數
參數描述
LPC2378FBD144,551 功能描述:ARM微控制器 - MCU ARM7 512KF/USB/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2378FBD144/CP32 制造商:NXP Semiconductors 功能描述:- Trays
LPC2378FBD144/CP3E 制造商:NXP Semiconductors 功能描述:
LPC2378FBD144551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU ARM7 72MHZ LQFP-144
LPC2378-STK 功能描述:開發板和工具包 - ARM DEV BRD FOR LPC2378 512KB FLASH 16KB RAM RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V