- 您現在的位置：買賣IC網 > PDF目錄385497 > LPC2926FBD144 (NXP SEMICONDUCTORS) ARM9 microcontroller with CAN, LIN, and USB PDF資料下載
參數資料
| 型號： | LPC2926FBD144 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | ARM9 microcontroller with CAN, LIN, and USB |
| 中文描述： | 32-BIT, FLASH, 125 MHz, RISC MICROCONTROLLER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT486-1, LQFP-144 |
| 文件頁數： | 43/95頁 |
| 文件大?。?/td> | 1855K |
| 代理商： | LPC2926FBD144 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁
LPC2926_27_29
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 5 — 28 September 2010
43 of 95
NXP Semiconductors
LPC2926/2927/2929
ARM9 microcontroller with CAN, LIN, and USB
Table 23.
Symbol
ADC0 IN[7:0]
[1]
VREFP, VREFN, V
DDA(ADC3V3)
must be connected for the 5 V ADC0 to operate properly.
The analog inputs of ADC0 are internally multiplied by a factor of 3.3 / 5. If V
DDA(ADC5V0)
is connected to
3.3 V, the maximum digital result is 1024
×
3.3 / 5.
[2]
[3]
V
DDA(ADC5V0)
and V
DDA(ADC3V3)
must be set as follows: V
DDA(ADC5V0)
= V
DDA(ADC3V3)
×
1.5.
Remark:
The following formula only applies to ADC0:
Voltage variations on VREFP (i.e. those that deviate from voltage variations on the
V
DDA(ADC5V5)
pin) are visible as variations in the measurement result. The following
formula is used to determine the conversion result of an input voltage V
I
on ADC0:
(3)
Remark:
Note that the ADC1 and ADC2 accept an input voltage up to of 3.6 V (see
Table 34
) on the ADC1/2 IN pins. If the ADC is not used, the pins are 5 V tolerant. The
ADC0 pins are 5 V tolerant.
6.15.4.3
Clock description
The ADC modules are clocked from two different sources; CLK_MSCSS_ADCx_APB and
CLK_ADCx (x = 0, 1, or 2), see
Section 6.7.2
. Note that each ADC has its own
CLK_ADCx and CLK_MSCSS_ADCx_APB branch clocks for power management. If an
ADC is unused both its CLK_MSCSS_ADCx_APB and CLK_ADCx can be switched off.
The frequency of all the CLK_MSCSS_ADCx_APB clocks is identical to
CLK_MSCSS_APB since they are derived from the same base clock
BASE_MSCSS_CLK. Likewise the frequency of all the CLK_ADCx clocks is identical
since they are derived from the same base clock BASE_ADC_CLK.
The register interface towards the system bus is clocked by CLK_MSCSS_ADCx_APB.
Control logic for the analog section of the ADC is clocked by CLK_ADCx, see also
Figure 9
.
ADC pins
Pin name
IN0[7:0]
Direction Description
IN
analog input for 5.0 V ADC0, channel 7 to
channel 0.
IN
analog input for 3.3 V ADC1/2, channel 7 to
channel 0.
IN
ADC external start-trigger input.
IN
ADC LOW reference level.
IN
ADC HIGH reference level.
V
DDA(ADC5V0)
[1]
IN
5 V high-power supply and HIGH reference for
ADC0. Connect to clean 5 V as HIGH
reference. May also be connected to 3.3 V if
3.3 V measurement range for ADC0 is
needed.
[2][3]
V
DDA(ADC3V3)
IN
ADC1 and ADC2 3.3 V supply (also used for
ADC0).
[3]
ADC1/2 IN[7:0]
IN1/2[7:0]
ADC2_EXT_START
VREFN
VREFP
V
DDA(ADC5V0)
CAP1[2]
VREFN
VREFP
V
DDA(ADC3V3)
2
3
--
V
I
1
2
--
V
DDA ADC5V0
)
–
1
2
--
V
DDA ADC3V3
)
+
–
V
VREFP
V
VREFN
-------------------------------------------
×
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2927FBD144 | ARM9 microcontroller with CAN, LIN, and USB |
| LPC2929FBD144 | ARM9 microcontroller with CAN, LIN, and USB |
| LPC2930FBD208 | ARM9 flashless microcontroller with CAN, LIN, and USB |
| LPC2939FBD208 | ARM9 microcontroller with CAN, LIN, and USB |
| LPC3180FEL320 | 16-32-bit ARM microcontroller; hardware floating-point coprocessor, USB On-The-Go, and SDRAM memory interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2926FBD144,557 | 制造商:NXP Semiconductors 功能描述:LPC2926FBD144/LQFP144/TRAYDPM/ - Trays 制造商:NXP Semiconductors 功能描述:IC MCU ARM9 256KB FLASH 144LQFP |
| LPC2927 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB |
| LPC2927_10 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB |
| LPC2927FBD144 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB |
| LPC2927FBD144,551 | 功能描述:ARM微控制器 - MCU ARM968 512K FL/16K RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。