參數資料
型號: LPC47M14L-NC
廠商: SMSC Corporation
英文描述: EZ STIX CABLE INSTALLER STICKS
中文描述: 128引腳ENGANCED超級I / O與LPC接口和USB集線器控制器
文件頁數: 67/205頁
文件大小: 1219K
代理商: LPC47M14L-NC
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁
SMSC DS – LPC47M14X
Page 67
Rev. 03/19/2001
50% duty cycle. If a 3 or greater is loaded the output is low for 2 bits and high for the remainder of the count. The input
clock to the BRG is a 1.8462 MHz clock.
Table 31 shows the baud rates possible.
Effect Of The Reset on Register File
The Reset Function (details the effect of the Reset input on each of the registers of the Serial Port.
FIFO INTERRUPT MODE OPERATION
When the RCVR FIFO and receiver interrupts are enabled (FCR bit 0 = "1", IER bit 0 = "1"), RCVR interrupts occur as
follows:
The receive data available interrupt will be issued when the FIFO has reached its programmed trigger level; it is
cleared as soon as the FIFO drops below its programmed trigger level.
The IIR receive data available indication also occurs when the FIFO trigger level is reached. It is cleared when
the FIFO drops below the trigger level.
The receiver line status interrupt (IIR=06H), has higher priority than the received data available (IIR=04H)
interrupt.
The data ready bit (LSR bit 0) is set as soon as a character is transferred from the shift register to the RCVR
FIFO. It is reset when the FIFO is empty.
When RCVR FIFO and receiver interrupts are enabled, RCVR FIFO timeout interrupts occur as follows:
1)
A FIFO timeout interrupt occurs if all the following conditions exist:
At least one character is in the FIFO.
The most recent serial character received was longer than 4 continuous character times ago. (If 2 stop bits
are programmed, the second one is included in this time delay).
The most recent CPU read of the FIFO was longer than 4 continuous character times ago.
This will cause a maximum character received to interrupt issued delay of 160 msec at 300 BAUD with a 12 bit
character.
Character times are calculated by using the RCLK input for a clock signal (this makes the delay proportional
to the baudrate).
When a timeout interrupt has occurred it is cleared and the timer reset when the CPU reads one character
from the RCVR FIFO.
When a timeout interrupt has not occurred the timeout timer is reset after a new character is received or after
the CPU reads the RCVR FIFO.
When the XMIT FIFO and transmitter interrupts are enabled (FCR bit 0 = "1", IER bit 1 = "1"), XMIT interrupts occur as
follows:
The transmitter holding register interrupt (02H) occurs when the XMIT FIFO is empty; it is cleared as soon as
the transmitter holding register is written to (1 of 16 characters may be written to the XMIT FIFO while
servicing this interrupt) or the IIR is read.
The transmitter FIFO empty indications will be delayed 1 character time minus the last stop bit time whenever
the following occurs: THRE=1 and there have not been at least two bytes at the same time in the transmitter
FIFO since the last THRE=1. The transmitter interrupt after changing FCR0 will be immediate, if it is enabled.
Character timeout and RCVR FIFO trigger level interrupts have the same priority as the current received data available
interrupt; XMIT FIFO empty has the same priority as the current transmitter holding register empty interrupt.
相關PDF資料
PDF描述
LPC47M14M-NC CAT5 MULTI 1X9 VIDEO DISTRIBUTION AMP
LPC47M14Q-NC HD VIEW RECEIVER 2 PORT DAISYCHAINABLE
LPC47M14V-NC AT PRINTER SERIAL CBL DB9 FEMALE - DB25 MALE
LPC47M14R-NC 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB
LPC47M14I-NC 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB
相關代理商/技術參數
參數描述
LPC47M14M-NC 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB
LPC47M14N-NC 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB
LPC47M14O-NC 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB
LPC47M14P-NC 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB
LPC47M14Q-NC 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB