- 您現在的位置：買賣IC網 > PDF目錄358934 > LPC47M192-NC (STANDARD MICROSYSTEMS CORP) LPC SUPER I/O WITH HARDWARE MONITORING BLOCK PDF資料下載
參數資料
| 型號： | LPC47M192-NC |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | LPC SUPER I/O WITH HARDWARE MONITORING BLOCK |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQFP128 |
| 封裝： | 14 X 20 MM, 2.70 MM THICKNESS, QFP-128 |
| 文件頁數： | 136/228頁 |
| 文件大?。?/td> | 1269K |
| 代理商： | LPC47M192-NC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁當前第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁
Temperature High Limit 1 or 2 register and Remote Temperature Low Limit 1 or 2 register, then the Remote Temp
Error 1 or 2 status bit is set in the Interrupt Status Register 1.
There are Remote Diode Fault status 1 and 2 bits in the Status Register 2 (0x42). The LPC47M192 automatically
sets the associated diode fault bit to 1 when there is an open circuit fault on the Remote x+ or Remote x- thermal
diode input pins. The occurrence of either a short
(D+ and D- shorted together)
or open circuit fault will cause 80h to
be loaded into the associated reading register, which will cause the corresponding remote temp error bit to be set.
This will cause the THERM# pin to become active if enabled.
This same operation applies (including the diode
fault bit getting set) for the following board design error conditions: D+ shorted to VCC, D- shorted to VCC,
D+ shorted to ground. The diode fault bit will also be set if D- is shorted to ground, however, the part will
give a valid temperature reading (with some error), so the out of limit bit will not be set and therefore the
THERM# pin will not go active for this condition.
. Before a remote diode conversion is updated, the status of the
remote diode is checked.
The temperature change is computed by measuring the change in Vbe at two different operating points of the diode
to which the Dx+ and Dx- pins are connected. But accuracy of the measurement also depends on non-ideality factor
of the process the diode is manufactured on. See “Appendix A – Thermal Diode Parameters” for relationship
between the non-ideality factor and the change in Vbe.
Note
: Since digital boards can be electrically noisy environments that may interfere when measuring very small
voltages from a remote diode sensor, special layout considerations should be made. See “Layout Considerations”
below.
SMSC DS – LPC47M192
Page 136
Rev. 03/30/05
DATASHEET
7.18.3.9.3 Temperature Data Format
Temperature data can be read from the three temperature registers. One is the Ambient Temperature Reading
register (0x27), the second is the Remote Diode Temperature Reading 1 register (0x26), and the third is the Remote
Diode Temperature Reading 2 register (0x52).
The following table shows the corresponding format of the temperature digital data, represented by an 8-bit, two’s
complement word with an LSB equal to 1.0
C.
Temperature
+125
0
C
+25
0
C
+1.0
0
C
0
0
C
-1.0
0
C
-25
0
C
-40
0
C
Digital Output
0111 1101
0001 1001
0000 0001
0000 0000
1111 1111
1110 0111
1101 1000
7.18.3.9.4 Offset Register
Offset Register 1 is used for internal or remote temperature 1 reading. The Offset Register 1 (1Fh) contain a 2's
complement value which is added (or subtracted if the number is negative) to the temperature reading. The default
value in the offset register is zero, so initially zero is always added to the temperature reading. This offset register is
configured for the external temperature channel by default. It may be switched to the internal channel by setting bit 4
of the Special Function Register to 1.
7.18.3.9.5 Second Offset Register
The Offset Register 2 at 1Eh is for second remote diode temperature reading. This register contains a 2's
complement value which is added (or subtracted if the number is negative) to the second external temperature
reading. Note that the default value in the offset register is zero, so initially zero is always added to the second
temperature reading. This offset register only applies to remote diode temperature reading 2. No configuration bit is
required.
7.18.3.10 Thermal / Voltage Interrupt Pin
The THERM# function is multiplexed on A0/RESET#/THERM#/XNOR_OUT pin. This function is used as an interrupt
output for out-of-limit temperature events. It can also be enabled for out-of-limit voltage events.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC47M192-NW | LPC SUPER I/O WITH HARDWARE MONITORING BLOCK |
| LPC47S422-MS | ENHANCED SUPER I/O WITH LPC INTERFACE FOR SERVER APPLICATIONS |
| LPC47S422QFP | ENHANCED SUPER I/O WITH LPC INTERFACE FOR SERVER APPLICATIONS |
| LPC47U33x | 100 Pin Enhanced Super I/O for LPC Bus with Consumer Features and SMBus Controller |
| LPC870-FJ | Mini SIDELED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC47M192-NW | 功能描述:輸入/輸出控制器接口集成電路 Super I/O Contrllr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| LPC47M262-NU | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述: |
| LPC47M262-NU WAF | 制造商:SMSC 功能描述: |
| LPC47M287-NR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LPC47M287-NW | 功能描述:輸入/輸出控制器接口集成電路 Enhanced Super I/O RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。