參數資料
型號： LS4301-7R
英文描述： 100 Watt AC-DC Converters with PFC
中文描述： 100瓦交直流轉換器的功率因數校正
文件頁數： 9/27頁
文件大?。?/td> 599K
代理商： LS4301-7R
Cassette Style
100 Watt AC-DC Converters
S Series PFC
Edition 01/01.2001
9/27
Output Voltage Regulation of Double Output Modules
Output 1 is under normal conditions regulated to U
o1 nom
,
independent of the output currents.
U
o2
is dependent upon the load distribution. If both outputs
are loaded with more than 10% of I
o nom
, the deviation of
U
o2
remains within
±
5% of the value of U
o1
. The following 3
fi
gures show the regulation with varying load distribution. If
I
o1
= I
o2
or the two outputs are connected in series, the de-
viation of U
o2
remains within
±
1% of the value of U
o1
pro-
vided that a total load of more than 10% of I
o nom
is applied.
Two outputs of a single S 5000 module connected in paral-
lel will behave like the output of a S 4000 module; the paral-
leled output is fully regulated. No precautions are neces-
sary in using the R-input and the test sockets.
U
o
U
o nom
0.98
0.5
0
0.5
1.0
I
o1
I
oL
I
o
I
o nom
05001
Fig. 9
U
o1
vs. I
o1
(typ.) of single output units
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature T
A max
(see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the Measuring point of case
temperature T
C
(see: Mechanical Data) will approach the
indicated value T
C max
after the warm-up phase. However,
the relationship between T
A
and T
C
depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces. T
A max
is therefore, contrary to T
C max
,
an indicative value only.
Caution:
The installer must ensure that under all operat-
ing conditions T
C
remains within the limits stated in the
table: Temperature specifications.
Notes:
Sufficient forced cooling or an additional heat sink
allows T
A
to be higher than 71
°
C (e.g. 85
°
C) if T
C max
is not
exceeded.
For -7 or -9 units at an ambient temperature T
A
of 85
°
C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
I
o
/
I
o nom
T
A
[
°
C]
0.9
1.0
Forced cooling
0
T
A min
T
C max
Convection cooling
Fig. 8
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
T
C max
. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diodes
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
–
Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
–
Not more than 5 units should be connected in parallel.
–
Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
–
The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
Output Voltage Regulation of Single or Double Output
Modules with Outputs 1 and 2 Connected in Series
相關PDF資料
PDF描述
LS5540-7R 100 Watt AC-DC Converters with PFC
LS5660-7R 100 Watt AC-DC Converters with PFC
LS4501-7R 100 Watt AC-DC Converters with PFC
LS4601-7R 100 Watt AC-DC Converters with PFC
LS505 LS505 - Symmetrical peak clipping in a feedback configuration
相關代理商/技術參數
參數描述
LS4301-9ER 制造商:Power-One 功能描述:ACDC - Bulk
LS430850 功能描述:SCR MOD ISO SGL 800V 500A RoHS:是 類別:半導體模塊 >> SCR 系列:- 其它有關文件:SCR Module Selection Guide 標準包裝:10 系列:- 結構:串聯 - SCR/二極管 SCR 數目，二極管:1 SCR，1 個二極管 電壓 - 斷路:1600V 電流 - 柵極觸發電流 (Igt)（最大）:150mA 電流 - 導通狀態 (It (AV))（最大）:95A 電流 - 導通狀態 (It (RMS))（最大）:210A 電流 - 非重復電涌，50、60Hz (Itsm):1785A，1870A 電流 - 維持(Ih):250mA 安裝類型:底座安裝 封裝/外殼:ADD-A-PAK（3 + 2） 包裝:散裝 其它名稱:*IRKL92/16AIRKL92/16IRKL92/16-ND
LS4-30I 制造商:Panduit Corp 功能描述:
LS4-31 制造商:Panduit Corp 功能描述:
LS431050 功能描述:SCR MOD ISO SGL 1000V 500A RoHS:是 類別:半導體模塊 >> SCR 系列:- 其它有關文件:SCR Module Selection Guide 標準包裝:10 系列:- 結構:串聯 - SCR/二極管 SCR 數目，二極管:1 SCR，1 個二極管 電壓 - 斷路:1600V 電流 - 柵極觸發電流 (Igt)（最大）:150mA 電流 - 導通狀態 (It (AV))（最大）:95A 電流 - 導通狀態 (It (RMS))（最大）:210A 電流 - 非重復電涌，50、60Hz (Itsm):1785A，1870A 電流 - 維持(Ih):250mA 安裝類型:底座安裝 封裝/外殼:ADD-A-PAK（3 + 2） 包裝:散裝 其它名稱:*IRKL92/16AIRKL92/16IRKL92/16-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*