- 您現在的位置：買賣IC網 > PDF目錄367589 > LS5540-7R 100 Watt AC-DC Converters with PFC PDF資料下載
參數資料
| 型號： | LS5540-7R |
| 英文描述： | 100 Watt AC-DC Converters with PFC |
| 中文描述： | 100瓦交直流轉換器的功率因數校正 |
| 文件頁數： | 11/27頁 |
| 文件大?。?/td> | 599K |
| 代理商： | LS5540-7R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Cassette Style
100 Watt AC-DC Converters
S Series PFC
Edition 01/01.2001
11/27
0
t
t
0
Inhibit
1
0.1
1
U
o
/U
o nom
t
r
t
f
06001
Fig. 19
Output response as a function of inhibit control
Auxiliary Functions
i Inhibit for Remote On and Off
Note:
With open i input: Output is disabled (U
o
= off).
The outputs of the module may be enabled or disabled by
means of a logic signal (TTL, CMOS, etc.) applied between
the inhibit input i and the negative pin of output 1 (Vo1
–
). In
systems with several units, this feature can be used, for ex-
ample, to control the activation sequence of the converters.
If the inhibit function is not required, connect the inhibit pin
18 to pin 14 to enable the outputs (active low logic, fail
safe). For output response refer to: Hold-up Time and Out-
put Response
Vi+
Vi
–
Vo
–
i
Vo+
I
inh
U
inh
06031
1.6
0.8
0
–
0.8
–
50
U
inh
[V]
I
inh
[mA]
–
30
0
–
10
10
30
50
2.0
1.2
0.4
–
0.4
U
inh
= 0.8 V
U
o
= on
U
o
= off
U
inh
= 2.4 V
0
Fig. 17
Definition of U
inh
and I
inh
.
Fig. 18
Typical inhibit current I
inh
versus inhibit voltage U
inh
Table 5: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
U
inh
Inhibit
voltageU
o
= off
U
o
= on
U
i min
…
U
i max
–
50
0.8
V
2.4
50
I
inh
Inhibit current
U
inh
= 0
–
400
μ
A
t
r
Rise time
30
ms
t
f
Fall time
depending on I
o
Sense Lines
(Only for single output units 5.1 V, 12 V, 15 V, 24 V)
This feature enables for compensation of voltage drops
across the connector contacts and if necessary, across the
load lines. If the sense lines are connected at the load
rather than directly at the connector, the user should ensure
that U
o max
(between Vo1+ and Vo1
–
) is not exceeded. We
recommend connecting the sense lines directly at the fe-
male connector.
For further information, please refer to: Application Notes .
To ensure correct operation, both sense lines (S+ and S
–
)
should be connected to their respective power outputs
(Vo1+ and Vo1
–
) and the voltage difference between any
sense line and its respective power output pin (as meas-
ured on the connector) should not exceed the following val-
ues:
Table 6: Maximum Voltage compensation allowed using
sense lines
Output
voltage
Total voltage difference
between sense lines and
their respective outputs
Voltage difference
between
Vo
–
and S
–
5.1 V
<
0.5 V
<
1.0 V
<
0.25 V
<
0.25 V
12 V, 15 V
If the output voltages are increased above U
o nom
via R-in-
put control, option P setting, remote sensing or option T, the
output currents must be reduced accordingly so that
P
o nom
is not exceeded.
Important:
The output terminals Vo1+ and Vo1
–
must
always be connected to the load before connecting the
sense lines S+ and S
–
, otherwise the unit will be dam-
aged.
相關PDF資料 |
PDF描述 |
|---|---|
| LS5660-7R | 100 Watt AC-DC Converters with PFC |
| LS4501-7R | 100 Watt AC-DC Converters with PFC |
| LS4601-7R | 100 Watt AC-DC Converters with PFC |
| LS505 | LS505 - Symmetrical peak clipping in a feedback configuration |
| LS505MCRO | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LS5540-9ER | 制造商:Power-One 功能描述:ACDC - Bulk |
| LS5-544 | 功能描述:打印機 LS5, Laminated Continuous Tape, Polyeste RoHS:否 制造商:Seiko Instruments 產品:Printer 電源電壓: 每行點數:9 x 320 打印速度:52.5 cps, 80 cps 紙張寬度:112 mm |
| LS5-547 | 制造商:Panduit Corp 功能描述: |
| LS5-60 | 制造商:Panduit Corp 功能描述: |
| LS-560M2H---2225S | 制造商:Surge Components Inc 功能描述:CAP ALUM 56UF 500V ?20% 2000LHRS 22 X 25 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。