- 您現在的位置：買賣IC網 > PDF目錄224113 > LT1074HVIT7#35 (LINEAR TECHNOLOGY CORP) 8.5 A SWITCHING REGULATOR, 125 kHz SWITCHING FREQ-MAX, PZFM7 PDF資料下載
參數資料
| 型號： | LT1074HVIT7#35 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 8.5 A SWITCHING REGULATOR, 125 kHz SWITCHING FREQ-MAX, PZFM7 |
| 封裝： | PLASTIC, TO-220, 7 PIN |
| 文件頁數： | 16/17頁 |
| 文件大?。?/td> | 201K |
| 代理商： | LT1074HVIT7#35 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁
LT1074/LT1076
8
sn1074 1074fds
Figure 1. Input Capacitor Ripple
Figure 2. Proper Ground Pin Connection
VIN PIN
The VIN pin is both the supply voltage for internal control
circuitry and one end of the high current switch. It is
important,
especially at low input voltages, that this pin be
bypassed with a low ESR, and low inductance capacitor to
prevent transient steps or spikes from causing erratic
operation. At full switch current of 5A, the switching
transients at the regulator input can get very large as
shown in Figure 1. Place the input capacitor very close to
the regulator and connect it with wide traces to avoid extra
inductance. Use radial lead capacitors.
FEEDBACK PIN
The feedback pin is the inverting input of an error amplifier
which controls the regulator output by adjusting duty
cycle. The noninverting input is internally connected to a
trimmed 2.21V reference. Input bias current is typically
0.5
A when the error amplifier is balanced (IOUT = 0). The
error amplifier has asymmetrical GM for large input sig-
nals to reduce startup overshoot. This makes the amplifier
more sensitive to large ripple voltages at the feedback pin.
100mVp-p ripple at the feedback pin will create a 14mV
offset in the amplifier, equivalent to a 0.7% output voltage
shift. To avoid output errors, output ripple (P-P) should be
less than 4% of DC output voltage at the point where the
output divider is connected.
See the “Error Amplifier” section for more details.
Frequency Shifting at the Feedback Pin
The error amplifier feedback pin (FB) is used to downshift
the oscillator frequency when the regulator output voltage
is low. This is done to guarantee that output short-circuit
DESCRIPTIO S
U
PI
U
LP = Total inductance in input bypass connections
and capacitor.
“Spike” height (dI/dt LP) is approximately 2V per
inch of lead length for LT1074 and 0.8V per inch for
LT1076.
“Step” for ESR = 0.05
and ISW = 5A is 0.25V.
“Ramp” for C = 200
F, TON = 5s, and ISW = 5A,
is 0.12V.
Input current on the VIN Pin in shutdown mode is the sum
of actual supply current (
≈140A, with a maximum of
300
A), and switch leakage current. Consult factory for
special testing if shutdown mode input current is critical.
GROUND PIN
It might seem unusual to describe a ground pin, but in the
case of regulators, the ground pin must be connected
properly to ensure good load regulation. The internal
reference voltage is referenced to the ground pin; so any
error in ground pin voltage will be multiplied at the output;
LT1074PD01
()
ISW
()
ESR
STEP =
()
ISW
()
TON
RAMP =
()()L
P
dl
dt
C
FB
GND
LT1074
LT1074PD02
R2
HIGH CURRENT
RETURN PATH
NEGATIVE OUTPUT NODE
WHERE LOAD REGULATION
WILL BE MEASURED
V
VV
OUT
GND
OUT
= ()(
)
221
.
To ensure good load regulation, the ground pin must be
connected directly to the proper output node, so that no
high currents flow in this path. The output divider resistor
should also be connected to this low current connection
line as shown in Figure 2.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1422IS8#PBF | Hot Swap Controller; Package: SO; No of Pins: 8; Temperature Range: -40°C to +85°C |
| LTC1422IS8#TRPBF | Hot Swap Controller; Package: SO; No of Pins: 8; Temperature Range: -40°C to +85°C |
| LTC1426CMS8#PBF | Micropower Dual 6-Bit PWM DAC; Package: MSOP; No of Pins: 8; Temperature Range: 0°C to +70°C |
| LTC1426CMS8#TRPBF | Micropower Dual 6-Bit PWM DAC; Package: MSOP; No of Pins: 8; Temperature Range: 0°C to +70°C |
| LTC1426CS8#PBF | Micropower Dual 6-Bit PWM DAC; Package: SO; No of Pins: 8; Temperature Range: 0°C to +70°C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1074HVIT7PBF | 制造商:Linear Technology 功能描述:Switching Regulator Step-Down 5A TO220-7 |
| LT1074HVITPBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Down 8-60V TO220-5 |
| LT1074IT | 功能描述:IC REG MULTI CONFIG ADJ TO220-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1074IT#06 | 制造商:Linear Technology 功能描述:Step-Down Switching Regulator |
| LT1074IT#06PBF | 功能描述:IC REG MULTI CONFIG ADJ TO220-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。