3
LT1207
VCM = 0, ±5V ≤ VS ≤ ±15V, pulse tested, VSHDN A = 0V, VSHDN B = 0V, unless otherwise noted.
ELECTRICAL CHARACTERISTICS
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Noninverting Input Current
VS = ±5V to ±15V
q
30
500
nA/V
Power Supply Rejection
Inverting Input Current
VS = ±5V to ±15V
q
0.7
5
A/V
Power Supply Rejection
AV
Large-Signal Voltage Gain
VS = ±15V, VOUT = ±10V, RL = 50
q
55
71
dB
VS = ±5V, VOUT = ±2V, RL = 25
q
55
68
dB
ROL
Transresistance,
VOUT/IIN–
VS = ±15V, VOUT = ±10V, RL = 50
q
100
260
k
VS = ±5V, VOUT = ±2V, RL = 25
q
75
200
k
VOUT
Maximum Output Voltage Swing
VS = ±15V, RL = 50, TA = 25°C
±11.5
±12.5
V
q
±10.0
V
VS = ±5V, RL = 25, TA = 25°C
±2.5
±3.0
V
q
±2.0
V
IOUT
Maximum Output Current
RL = 1
q
250
500
1200
mA
IS
Supply Current per Amplifier
VS = ±15V, VSHDN = 0V, TA = 25°C20
30
mA
q
35
mA
Supply Current per Amplifier,
VS = ±15V, TA = 25°C12
17
mA
RSHDN = 51k (Note 4)
Positive Supply Current
VS = ±15V, VSHDN A = 15V, VSHDN B = 15V
q
200
A
per Amplifier, Shutdown
Output Leakage Current, Shutdown
VS = ±15V, VSHDN = 15V, VOUT = 0V
q
10
A
SR
Slew Rate (Note 5)
AV = 2, TA = 25°C
400
900
V/
s
Differential Gain (Note 6)
VS = ±15V, RF = 560, RG = 560, RL = 30
0.02
%
Differential Phase (Note 6)
VS = ±15V, RF = 560, RG = 560, RL = 30
0.17
DEG
BW
Small-Signal Bandwidth
VS = ±15V, Peaking ≤ 0.5dB
60
MHz
RF = RG = 620, RL = 100
VS = ±15V, Peaking ≤ 0.5dB
52
MHz
RF = RG = 649, RL = 50
VS = ±15V, Peaking ≤ 0.5dB
43
MHz
RF = RG = 698, RL = 30
VS = ±15V, Peaking ≤ 0.5dB
27
MHz
RF = RG = 825, RL = 10
Note 3: Thermal resistance
θJA varies from 40°C/W to 60°C/W depending
upon the amount of PC board metal attached to the device.
θJA is specified
for a 2500mm2 test board covered with 2oz copper on both sides.
Note 4: RSHDN is connected between the Shutdown pin and ground.
Note 5: Slew rate is measured at
±5V on a ±10V output signal while
operating on
±15V supplies with RF = 1.5k, RG = 1.5k and RL = 400.
Note 6: NTSC composite video with an output level of 2V.
The q denotes specifications which apply for 0
°C ≤ TA ≤ 70°C.
Note 1: Applies to short circuits to ground only. A short circuit between
the output and either supply may permanently damage the part when
operated on supplies greater than
±10V.
Note 2: Commercial grade parts are designed to operate over the
temperature range of – 40
°C to 85°C but are neither tested nor guaranteed
beyond 0
°C to 70°C. Industrial grade parts tested over –40°C to 85°C are
available on special request. Consult factory.