- 您現在的位置：買賣IC網 > PDF目錄5730 > LT1207CS (Linear Technology)IC CURRNT FEEDBK AMP DUAL 16SOIC PDF資料下載
參數資料
| 型號： | LT1207CS |
| 廠商： | Linear Technology |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CURRNT FEEDBK AMP DUAL 16SOIC |
| 標準包裝： | 50 |
| 放大器類型： | 電流反饋 |
| 電路數： | 2 |
| 轉換速率： | 900 V/µs |
| -3db帶寬： | 60MHz |
| 電流 - 輸入偏壓： | 10µA |
| 電壓 - 輸入偏移： | 3000µV |
| 電流 - 電源： | 20mA |
| 電流 - 輸出 / 通道： | 1.2A |
| 電壓 - 電源，單路/雙路(±)： | 10 V ~ 30 V，±5 V ~ 15 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SO |
| 包裝： | 管件 |
11
LT1207
Figure 5c. Large-Signal Response, AV = 2
Capacitance on the Inverting Input
Current feedback amplifiers require resistive feedback
from the output to the inverting input for stable operation.
Take care to minimize the stray capacitance between the
output and the inverting input. Capacitance on the invert-
ing input to ground will cause peaking in the frequency
response (and overshoot in the transient response), but it
does not degrade the stability of the amplifier.
Power Supplies
The LT1207 will operate from single or split supplies from
±5V (10V total) to ±15V (30V total). It is not necessary to
use equal value split supplies, however the offset voltage
and inverting input bias current will change. The offset
voltage changes about 500
V per volt of supply mis-
match. The inverting bias current can change as much as
5
A per volt of supply mismatch, though typically the
change is less than 0.5
A per volt.
Thermal Considerations
Each amplifier in the LT1207 includes a separate thermal
shutdown circuit which protects against excessive inter-
nal (junction) temperature. If the junction temperature
exceeds the protection threshold, the amplifier will begin
cycling between normal operation and an off state. The
cycling is not harmful to the part. The thermal cycling
occurs at a slow rate, typically 10ms to several seconds,
which depends on the power dissipation and the thermal
time constants of the package and heat sinking. Raising
the ambient temperature until the device begins thermal
shutdown gives a good indication of how much margin
there is in the thermal design.
Heat flows away from the amplifier through the package’s
copper lead frame. Heat sinking is accomplished by using
the heat spreading capabilities of the PC board and its
copper traces. Experiments have shown that the heat
spreading copper layer does not need to be electrically
connected to the tab of the device. The PCB material can
be very effective at transmitting heat between the pad area
attached to the tab of the device and a ground or power
plane layer either inside or on the opposite side of the
board. Although the actual thermal resistance of the PCB
material is high, the length/area ratio of the thermal
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
LT1207 F05c
RF = 750
RL = 50
Differential Input Signal Swing
The differential input swing is limited to about
±6V by an
ESD protection device connected between the inputs. In
normal operation, the differential voltage between the
input pins is small, so this clamp has no effect; however,
in the shutdown mode the differential swing can be the
same as the input swing. The clamp voltage will then set
the maximum allowable input voltage. To allow for some
margin, it is recommended that the input signal be less
than
±5V when the device is shut down.
LT1207 F06
Figure 6. Large-Signal Response, CL = 10,000pF
VS = ±15V
RF = RG = 3k
RL =
∞
at this rate is 1mA per picofarad of capacitance, so
10,000pF would require 10A! The photo (Figure 6) shows
the large-signal behavior with CL = 10,000pF. The slew
rate is about 60V/
s, determined by the current limit of
600mA.
相關PDF資料 |
PDF描述 |
|---|---|
| 77313-118-48LF | BERGSTIK |
| 3314-1002 | CONN HEADER 14POS R/A NO LATCH |
| 77313-102-48LF | CONN HEADER .100 DUAL STR 48POS |
| 65863-067 | QKE HDR |
| XG8W-3431 | PLUG 34POS DOUBLE ROW STRAIGHT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1207CS#PBF | 功能描述:IC CURRNT FEEDBK AMP DUAL 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| LT1207CS#TR | 功能描述:IC AMP CURR FEEDBACK DUAL 16SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| LT1207CS#TRPBF | 功能描述:IC CURRNT FEEDBK AMP DUAL 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| LT1208 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual and Quad 45MHz, 400V/us Op Amps |
| LT1208C | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual and Quad 45MHz, 400V/us Op Amps |
發布緊急采購，3分鐘左右您將得到回復。