VOUT AI04 Settling Time The characteristic curves show that t" />
參數資料
型號: LT1227CS8#PBF
廠商: Linear Technology
文件頁數: 12/12頁
文件大?。?/td> 0K
描述: IC VIDEO CURRNT FEEDBK AMP 8SOIC
標準包裝: 100
應用: 電流反饋
電路數: 1
-3db帶寬: 140MHz
轉換速率: 1100 V/µs
電流 - 電源: 10mA
電流 - 輸出 / 通道: 60mA
電壓 - 電源,單路/雙路(±): 4 V ~ 30 V,±2 V ~ 15 V
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 8-SOIC
包裝: 管件
產品目錄頁面: 1318 (CN2011-ZH PDF)
9
LT1227
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
VOUT
AI04
Settling Time
The characteristic curves show that the LT1227 amplifier
settles to within 10mV of final value in 40ns to 55ns for any
output step up to 10V. The curve of settling to 1mV of final
value shows that there is a slower thermal contribution up
to 20
s. The thermal settling component comes from the
output and the input stage. The output contributes just
under 1mV per volt of output change and the input
contributes 300
V per volt of input change. Fortunately
the input thermal tends to cancel the output thermal. For
this reason the noninverting gain of two configuration
settles faster than the inverting gain of one.
Large-Signal Transient Response, AV = –2
VOUT
AI04
Large-Signal Transient Response, AV = +2
Shutdown
The LT1227 has a high impedance, low supply current
mode which is controlled by Pin 8. In the shutdown mode,
the output looks like a 12pF capacitor and the supply
current drops to approximately the Pin 8 current. The
shutdown pin is referenced to the positive supply through
an internal pullup circuit (see the simplified schematic).
Pulling a current of greater than 50
A from Pin 8 will put
the device into the shutdown mode. An easy way to force
shutdown is to ground Pin 8, using open drain (collector)
logic. Because the pin is referenced to the positive supply,
the logic used should have a breakdown voltage of greater
than the positive supply voltage. No other circuitry is
necessary as an internal JFET limits the Pin 8 current to
about 100
A. When Pin 8 is open, the LT1227 operates
normally.
Differential Input Signal Swing
The differential input swing is limited to about
±6V by an
ESD protection device connected between the inputs. In
normal operation, the differential voltage between the
input pins is small, so this clamp has no effect; however,
in the shutdown mode, the differential swing can be the
same as the input swing. The clamp voltage will then set
the maximum allowable input voltage. To allow for some
margin, it is recommended that the input signal be less
than
±5V when the device is shutdown.
Offset Adjust
Pins 1 and 5 are provided for offset nulling. A small current
to V+ or ground will compensate for DC offsets in the
device. The pins are referenced to the positive supply (see
the simplified schematic) and should be left open if un-
used. The offset adjust pins act primarily on the inverting
input bias current. A 10k pot connected to Pins 1 and 5
with the wiper connected to V
+ will null out the bias
current, but will not affect the offset voltage much. Since
the output offset is
VO AV VOS + (IIN) RF
at higher gains (AV > 5), the VOS term will dominate. To null
out the VOS term, use a 10k pot between Pins 1 and 5 with
a 150k resistor from the wiper to ground for 15V split
supplies, 47k for 5V split supplies.
AI03
RF = 1k, RG= 1k, RL = 400
RF = 1k, RG= 510, RL = 400
相關PDF資料
PDF描述
VE-B63-MU CONVERTER MOD DC/DC 24V 200W
AD813ARZ-14 IC TRPL VIDEO AMP SNGL LP 14SOIC
VI-21J-IV-F1 CONVERTER MOD DC/DC 36V 150W
VE-B62-MU CONVERTER MOD DC/DC 15V 200W
VE-23R-IV-F2 CONVERTER MOD DC/DC 7.5V 150W
相關代理商/技術參數
參數描述
LT1227M 制造商:LINER 制造商全稱:Linear Technology 功能描述:140MHz Video Current Feedback Amplifier
LT1227MJ8 制造商:Linear Technology 功能描述:OP Amp Single Current Fdbk 15V 8-Pin CDIP
LT1228 制造商:LINER 制造商全稱:Linear Technology 功能描述:100MHz Current Feedback Amplifier with DC Gain Control
LT1228_07 制造商:LINER 制造商全稱:Linear Technology 功能描述:100MHz Current Feedback Amplifier with DC Gain Control
LT1228_12 制造商:LINER 制造商全稱:Linear Technology 功能描述:100MHz Current Feedback