- 您現在的位置：買賣IC網 > PDF目錄377704 > LT1506CR (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LT1506CR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 8.5 A SWITCHING REGULATOR, 560 kHz SWITCHING FREQ-MAX, PSSO7 |
| 封裝： | PLASTIC, D2PAK-7 |
| 文件頁數： | 13/24頁 |
| 文件大?。?/td> | 417K |
| 代理商： | LT1506CR |
13
LT1506
APPLICATIO
S I
N
FOR
ATIO
U
and does not fall to less than 1/3 of nominal output voltage,
foldback will not take effect. With the overloaded condi-
tion, output current will increase to a typical value of 5.7A,
determined by peak switch current limit of 6A. With
V
IN
= 15V, V
OUT
= 4V (5V overloaded) and I
OUT
= 5.7A:
(
15
W
U
I
A
D AVG
)
=
)
=
5 7 15 4
.
4 18
.
This is safe for short periods of time, but it would be
prudent to check with the diode manufacturer if continu-
ous operation under these conditions must be tolerated.
BOOST PIN CONSIDERATIONS
For most applications, the boost components are a 0.27
μ
F
capacitor and a 1N914 or 1N4148 diode. The anode is
connected to the regulated output voltage and this gener-
ates a voltage across the boost capacitor nearly identical
to the regulated output. In certain applications, the anode
may instead be connected to the unregulated input volt-
age. This could be necessary if the regulated output
voltage is very low (< 3V) or if the input voltage is less than
5V. Efficiency is not affected by the capacitor value, but the
capacitor should have an ESR of less than 1
to ensure
that it can be recharged fully under the worst-case condi-
tion of minimum input voltage. Almost any type of film or
ceramic capacitor will work fine.
For nearly all applications, a 0.27
μ
F boost capacitor works
just fine, but for the curious, more details are provided
here. The size of the boost capacitor is determined by
switch drive current requirements. During switch on time,
drain current on the capacitor is approximately I
OUT
/50. At
peak load current of 4.25A, this gives a total drain of 85mA.
Capacitor ripple voltage is equal to the product of on time
and drain current divided by capacitor value;
V = (t
ON
)(85mA/C). To keep capacitor ripple voltage to
less than 0.6V (a slightly arbitrary number) at the worst-
case condition of t
ON
= 1.8
μ
s, the capacitor needs to be
0.27
μ
F. Boost capacitor ripple voltage is not a critical
parameter, but if the minimum voltage across the capaci-
tor drops to less than 3V, the power switch may not
saturate fully and efficiency will drop. An approximate
formula for absolute minimum capacitor value is:
C
I
V
V
f V
( )
V
MIN
OUT
OUT
2 8
IN
)
OUT
=
(
)(
)
(
/
/
.
50
f = Switching frequency
V
OUT
= Regulated output voltage
V
IN
= Minimum input voltage
This formula can yield capacitor values substantially less
than 0.27
μ
F, but it should be used with caution since it
does not take into account secondary factors such as
capacitor series resistance, capacitance shift with tem-
perature and output overload.
SHUTDOWN FUNCTION AND UNDERVOLTAGE
LOCKOUT
Figure 4 shows how to add undervoltage lockout (UVLO)
to the LT1506. Typically, ULVO is used in situations where
the input supply is current limited or has a relatively high
source resistance. A switching regulator draws constant
power from the source, so source current increases as
source voltage drops. This looks like a negative resistance
load to the source and can cause the source to current limit
or latch low under low source voltage conditions. ULVO
prevents the regulator from operating at source voltages
where these problems might occur.
Threshold voltage for lockout is about 2.38V, slightly less
than the internal 2.42V reference voltage. A 3.5
μ
A bias
current flows outof the pin at threshold. This internally
generated current is used to force a default high state on
the shutdown pin if the pin is left open. When low shut-
down current is not an issue, the error due to this current
can be minimized by making R
LO
10k or less. If shutdown
current is an issue, R
LO
can be raised to 100k, but the error
due to initial bias current and changes with temperature
should be considered.
(
(
(
R
k
R
R
V
V
V R
A
LO
HI
LO
IN
LO
=
)
=
)
)
10
2 38
.
2 38
3 5
to 100k 25k suggested
V
IN
= Minimum input voltage
相關PDF資料 |
PDF描述 |
|---|---|
| LT1506CS8 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1506CS8-3.3 | RES 16.2K OHM 1/16W 1% 0402 SMD |
| LT1506IR | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1506IS8-3.3 | Octal D-Type Edge-Triggered Flip-Flops With 3-State Outputs 24-SOIC 0 to 70 |
| LT1506IR-SYNC | TERM. F/O CABLE ST-ST/ DPLX/RISER/5M/ORANGE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1506CR#PBF | 功能描述:IC REG BUCK ADJ 4.5A D2PAK RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1506CR#TR | 功能描述:IC REG BUCK ADJ 4.5A D2PAK RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1506CR#TRPBF | 功能描述:IC REG BUCK ADJ 4.5A D2PAK RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1506CR-3.3 | 功能描述:IC REG BUCK 3.3V 4.5A D2PAK RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1506CR-3.3#PBF | 功能描述:IC REG BUCK 3.3V 4.5A D2PAK RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2 |
發布緊急采購，3分鐘左右您將得到回復。