參數資料
型號： LT1533CS
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述： 1.8 A SWITCHING REGULATOR, 250 kHz SWITCHING FREQ-MAX, PDSO16
封裝： 0.150 INCH, PLASTIC, SOP-16
文件頁數： 14/20頁
文件大?。?/td> 379K
代理商： LT1533CS
14
LT1533
APPLICATIO
S I
FOR
ATIO
U
W
U
U
Ceramic: Generally used for high frequency and high
voltage bypass. If all ceramic capacitors are used, they can
have such a low ESR as to cause loop stability problems.
Often they can resonate with their ESL before ESR be-
comes effective.
Input Capacitor
The requirements for the input capacitor are less stringent
for this part. Input current ripple is lower because of the
push-pull action and low noise features of the part. How-
ever, the input capacitor should have low ESR at high
frequencies since this will be an important factor concern-
ing how much conducted noise is created. Values of input
capacitor will typically be in the 1
μ
F to 22
μ
F range with
ESR under 0.3
.
The input capacitor can see a high surge current when a
battery of high capacitance source is connected “l(fā)ive.”
Some solid tantalum capacitors can fail under this condi-
tion. Several manufacturers have developed a line of solid
tantalum capacitors specially tested for surge capability
(e.g., AVX TPS series). However, even these units may fail
if the input voltage approaches the maximum voltage
rating of the capacitor. AVX recommends derating capaci-
tor voltage by 2:1 for high surge applications.
Output Filter Capacitor
Output capacitors are usually chosen on the basis of ESR
since this will determine output ripple. Typical required
ESR will be in the 0.05
to 0.3
range.
The specific value for capacitance will depend on topol-
ogy. A typical output capacitor is an AVX type TPS, 22
μ
F
and 25V with a guaranteed ESR less than 0.2
. To further
reduce ESR, multiple output capacitors can be used in
parallel. The value in microfarads is not particularly impor-
tant. A small 22
μ
F tantalum capacitor will have high ESR
and higher output voltage ripple. Table 1 shows some
typical surface mount capacitors.
Table 1
SIZE
E CASE
CAPACITOR
AVX TPS, Sprague 593D
AVX TAJ
AVX TPS, Sprague 593D
AVX TAJ
Panasonic CD
AVX TPS
AVX TAJ
AVX TAJ
ESR (MAX
)
0.1 to 0.3
0.7 to 0.9
0.1 to 0.3
0.9 to 2.0
0.05 to 0.18
0.2 (Typ)
1.8 to 3.0
2.5 to 10
D CASE
C CASE
B CASE
Switching Diodes
In general, switching diodes should be Schottky diodes
such as 1N5818 or MBR130 (1A/30V). Low output current
applications may use 1N4148 switching diodes.
Unregulated Applications
The LT1533 can be used to create a low noise “DC
transformer” unregulated power supply. DC transformers
are open-loop switching regulators where the output
voltage is controlled by the turns ratio of the transformer.
A DC transformer provides a low cost isolated supply.
For such applications, the DUTY pin of the LT1533 should
be grounded. This will force the outputs into a 50% on,
50% off mode. Note that because of slew control there will
be some variance from 50%. Figure 6 shows a 5V to
±
12V
DC transformer.
One concern with this type of application is having both
switch outputs transition at the same time. This can cause
both primary side windings to have positive EMF added to
the winding, causing the current to run away. Since this
part controls slew rate this won’t happen. It is possible to
see slightly increased total current draw when both drivers
are on, but this will be controlled and observable. Since the
outputs share a common sense resistor, the outputs will
turn off when the total current in both exceeds the limit set
by the V
C
pin.
The FB pin should be DC biased between 0.7V and 1.2V to
prevent frequency shifting from occurring. This also en-
sures that the V
C
pin is set to its upper clamp, providing
peak output current.
相關PDF資料
PDF描述
LT1533 Octal Bus Transceivers 20-SOIC 0 to 70
LT1533I RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1533IS RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1783CS5 1.25MHz, Over-The-Top Micropower, Rail-to-Rail Input and Output Op Amp in SOT-23
LT1783CS6 1.25MHz, Over-The-Top Micropower, Rail-to-Rail Input and Output Op Amp in SOT-23
相關代理商/技術參數
參數描述
LT1533CS#PBF 功能描述:IC REG PUSH-PLL CTRLR ISO 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2
LT1533CS#TR 功能描述:IC REG PUSH-PLL CTRLR ISO 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1533CS#TRPBF 功能描述:IC REG PUSH-PLL CTRLR ISO 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1533CSPBF 制造商:Linear Technology 功能描述:Sw. Regulator Ultralow Noise 1A SOIC16
LT1533I 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultralow Noise 1A Switching Regulator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*