- 您現在的位置：買賣IC網 > PDF目錄377709 > LT1619EMS8 (LINEAR TECHNOLOGY CORP) Low Voltage Current Mode PWM Controller PDF資料下載
參數資料
| 型號： | LT1619EMS8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Low Voltage Current Mode PWM Controller |
| 中文描述： | 1.5 A SWITCHING CONTROLLER, 360 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 256K |
| 代理商： | LT1619EMS8 |
9
LT1619
1619fa
Diode
Schottky diodes are recommended for low output voltage
applications because of their low forward voltage. Since
Schottky diodes have negligible stored charge, charge
dumping loss is also reduced. The reverse breakdown
voltage of the diode should exceed the maximum reverse
voltage stress of the topology used. The diode should also
be able to carry the peak diode current with acceptable
foward voltage. For the boost converter in Figure 1, the
peak inductor current is approximately 5A. A Motorola
MBRD835 is used due to its low forward voltage.
Lowering Burst Mode Operation Current Limit
The LT1619 automatically enters Burst Mode operation as
V
C
voltage falls below V
B
. The corresponding switch
current is the Burst Mode operation switch current thresh-
old, I
D(BURST)
.
The effective Burst Mode operation current threshold can
be lowered by adding an offset to the input of the current
sense amplifier so that the switch current appears higher
to the PWM comparator. This has the effect of shifting the
V
C
operating range above V
B
. Although Burst Mode opera-
tion is not entirely disabled, the peak switch current before
entering Burst Mode operation is greatly reduced due to
the offset of the current sense amplifier. The peak switch
current is also determined by the current sense amplifier
blanking.
To lower the Burst Mode operation current sense thresh-
old, a resistor R
OS
is added between the SENSE pin and
the sense resistor R
SENSE
(Figure 5). The input bias
current I
BIAS
of the current sense amplifier, which has a
tolerance of
±
25% and is temperature stable, develops an
offset voltage at the sense input. The value of R
OS
required
for non-Burst Mode operation can be obtained with the
expression:
I
BIAS
R
OS
≥
V
SENSE(BURST)
where
V
SENSE(BURST)
= (Burst Mode operation peak switch
current, I
D(BURST)
) R
SENSE
For example, if I
BIAS
= 120
μ
A and V
SENSE(BURST)
= 10mV:
R
mV
μ
A
OS
≥
=
10
120
83
Allowing for 25% and 30% variations in I
BAIS
and
V
SENSE(BURST)
respectively:
R
OS
= (1.25)(1.3)(83
)
Choose R
OS
= 137
to completely disable Burst Mode
operation. Lower values of R
OS
(for example, 50
to
100
) can be used to lower the effective Burst Mode
current limit.
The value of the sense resistor is then adjusted to compen-
sate for the reduced full-scale sense voltage.
I
BIAS
R
OS
+ I
L(MAX)
R
SENSE
= 40mV
Filtering Current Sense Signal
I
n a current mode converter, the current sense circuit
senses the switch current and terminates the switch
conduction. In the LT1619, the current sense amplifier
has a full-scale input voltage range from the ground to the
current limit threshold (53mV). Due to high speed switch-
ing transients and parasitic trace inductances, the current
sense signal V
SENSE
tends to be noisy. If the V
SENSE
switching transient is excessive, the current sense ampli-
fier will amplify the spurious transient instead, resulting in
jittery operation. In situations where the internal leading
edge blanking is inadequate, a lowpass filter (Figure 6)
with corner frequency about 5 times the switching
fre
quency can be used to further attenuate high speed
switching transients. In Figure 6 the lowpass filter R
OS
and
C
S
has a corner frequency of:
Figure 5. Lowering Burst Mode Operation Current Limit
–
+
5
4
GND
SENSE
R
SENSE
R
OS
CURRENT
SENSE
AMPLIFIER
I
BIAS
= 120
μ
A
1619 F05
I
D
I
BIAS
= 120
μ
A
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT1620CS8 | Rail-to-Rail Current Sense Amplifier |
| LT1620IGN | CAP 0.1UF 200V 10% X7R SMD-1206 TR-7 PLATED-NI/SN |
| LT1621IGN | Rail-to-Rail Current Sense Amplifier |
| LT1620CGN | Rail-to-Rail Current Sense Amplifier |
| LT1620IS8 | Rail-to-Rail Current Sense Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1619EMS8#PBF | 功能描述:IC REG CTRLR PWM CM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LT1619EMS8#TR | 功能描述:IC REG CTRLR PWM CM 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LT1619EMS8#TRPBF | 功能描述:IC REG CTRLR PWM CM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LT1619EMS8PBF | 制造商:Linear Technology 功能描述:PWM Controller Current Mode 1.5A MSOP8 |
| LT1619ES8 | 功能描述:IC REG CTRLR PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。