VCSNK (Pin 12): Sink Current Limit Control Voltage In-
參數資料
型號: LT1970IFE
廠商: Linear Technology
文件頁數: 26/26頁
文件大?。?/td> 0K
描述: IC OP AMP 500MA ADJ 20-TSSOP
標準包裝: 74
放大器類型: 通用
電路數: 1
轉換速率: 1.6 V/µs
增益帶寬積: 3.6MHz
電流 - 輸入偏壓: 160nA
電壓 - 輸入偏移: 200µV
電流 - 電源: 7mA
電流 - 輸出 / 通道: 800mA
電壓 - 電源,單路/雙路(±): 5 V ~ 36 V,±2.5 V ~ 18 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)裸露焊盤
供應商設備封裝: 20-TSSOP-EP
包裝: 管件
LT1970
9
1970fc
PIN FUNCTIONS
VCSNK (Pin 12): Sink Current Limit Control Voltage In-
put. The current sink limit amplier will activate when
the sense voltage between SENSE+ and SENSEequals
–1.0 VVCSNK/10. VCSNK may be set between VCOMMON
and VCOMMON + 6V. The transfer function between VCSNK
and VSENSE is linear except for very small input voltages
at VCSNK < 60mV. VSENSE limits at a minimum set point of
4mV typical to insure that the sink and source limit ampli-
ers do not try to operate simultaneously. To force zero
output current, the ENABLE pin can be taken low.
VCSRC (Pin 13): Source Current Limit Control Voltage
Input. The current source limit amplier will activate when
the sense voltage between SENSE+ and SENSEequals
VVCSRC/10. VCSRC may be set between VCOMMON and
VCOMMON + 6V. The transfer function between VCSRC
and VSENSE is linear except for very small input voltages
at VCSRC < 60mV. VSENSE limits at a minimum set point
of 4mV typical to insure that the sink and source limit
ampliers do not try to operate simultaneously. To force
zero output current, the ENABLE pin can be taken low.
COMMON (Pin 14): Control and ENABLE inputs and ag
outputs are referenced to the COMMON pin. COMMON may
be at any potential between VEE and VCC – 3V. In typical
applications, COMMON is connected to ground.
ENABLE (Pin 15): ENABLE Digital Input Control. When
taken low this TTL-level digital input turns off the ampli-
er output and drops supply current to less than 1mA.
Use the ENABLE pin to force zero output current. Setting
VCSNK = VCSRC = 0V allows IOUT = ±4mV/RSENSE to ow
in or out of VOUT.
ISRC (Pin 16): Sourcing Current Limit Digital Output Flag.
ISRC is an open collector digital output. ISRC pulls low
whenever the sourcing current limit amplier assumes
control of the output. This pin can sink up to 10mA of
current. The current limit ag is off when the source
current limit is not active. ISRC, ISNK and TSD may be
wired “OR” together if desired. ISRC may be left open if
this function is not monitored.
ISNK (Pin 17): Sinking Current Limit Digital Output Flag.
ISNK is an open collector digital output. ISNK pulls low
whenever the sinking current limit amplier assumes
control of the output. This pin can sink up to 10mA of
current. The current limit ag is off when the source
current limit is not active. ISRC, ISNK and TSD may be
wired “OR” together if desired. ISNK may be left open if
this function is not monitored.
TSD (Pin 18): Thermal Shutdown Digital Output Flag. TSD
is an open collector digital output. TSD pulls low whenever
the internal thermal shutdown circuit activates, typically at
a die temperature of 160°C. This pin can sink up to 10mA
of output current. The TSD ag is off when the die tem-
perature is within normal operating temperatures. ISRC,
ISNK and TSD may be wired “OR” together if desired. ISNK
may be left open if this function is not monitored. Thermal
shutdown activation should prompt the user to evaluate
electrical loading or thermal environmental conditions.
V+ (Pin 19):
Output Stage Positive Supply. V+ may equal
VCC or may be smaller in magnitude. Only output stage
current ows through V+, all other current ows into VCC.
V+ may be used to drive the base/gate of an external power
device to boost the amplier’s output current to levels above
the rated 500mA of the on-chip output devices. Unless
used to drive boost transistors, V+ should be decoupled
to ground with a low ESR capacitor.
Package Base: The exposed backside of the package is
electrically connected to the VEE pins on the IC die. The
package base should be soldered to a heat spreading pad
on the PC board that is electrically connected to VEE.
相關PDF資料
PDF描述
951112-2530-AR-PT CONN HEADER 12POS 2MM VERT SMD
3-644632-2 CONN HEADER 2POS VERT .156 GOLD
3-644630-9 CONN HEADER 9POS R/A .156 GOLD
926142-01-05-I CONN HEADER 10POS DL .100 GOLD
3-644630-8 CONN HEADER 8POS R/A .156 GOLD
相關代理商/技術參數
參數描述
LT1970IFE#PBF 功能描述:IC OP AMP 500MA ADJ 20-TSSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
LT1970IFE#PBF 制造商:Linear Technology 功能描述:OP-AMP PRECISION 3.6MHZ 1.6 制造商:Linear Technology 功能描述:OP-AMP, PRECISION, 3.6MHZ, 1.6V/uS, TSSO
LT1970IFE#TR 功能描述:IC OPAMP ADJ PREC 500MA 20TSSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件
LT1970IFE#TRPBF 功能描述:IC OP AMP 500MA ADJ 20-TSSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件
LT1970IFEPBF 制造商:Linear Technology 功能描述:Op Amp Gen.Purpose +/-18V/36V TSSOP20EP