- 您現在的位置：買賣IC網 > PDF目錄6108 > LT6106CS5#TRMPBF (Linear Technology)IC AMP CURRENT SENSE TSOT23-5 PDF資料下載
參數資料
| 型號： | LT6106CS5#TRMPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP CURRENT SENSE TSOT23-5 |
| 標準包裝： | 1 |
| 放大器類型： | 電流檢測 |
| 電路數： | 1 |
| -3db帶寬： | 200kHz |
| 電流 - 輸入偏壓： | 40nA |
| 電壓 - 輸入偏移： | 150µV |
| 電流 - 電源： | 70µA |
| 電流 - 輸出 / 通道： | 1mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 36 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-5 細型，TSOT-23-5 |
| 供應商設備封裝： | TSOT-23-5 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1320 (CN2011-ZH PDF) |
| 其它名稱： | LT6106CS5#TRMPBFDKR |
LT6106
8
6106fa
APPLICATIONS INFORMATION
magnitude. A sense resistor with integrated Kelvin sense
terminals will give the best results. Figure 2 illustrates the
recommended method.
This approach can be helpful in cases where occasional
bursts of high currents can be ignored.
Care should be taken when designing the board layout for
RIN, especially for small RIN values. All trace and inter-
connect resistances will increase the effective RIN value,
causing a gain error.
Selection of External Output Resistor, ROUT
The output resistor, ROUT, determines how the output cur-
rent is converted to voltage. VOUT is simply IOUT ROUT.
In choosing an output resistor, the maximum output volt-
age must rst be considered. If the following circuit is a
buffer or ADC with limited input range, then ROUT must be
chosen so that IOUT(MAX) ROUT is less than the allowed
maximum input range of this circuit.
In addition, the output impedance is determined by ROUT. If
the circuit to be driven has high enough input impedance,
then almost any useful output impedance will be accept-
able. However, if the driven circuit has relatively low input
impedance, or draws spikes of current such as an ADC
might do, then a lower ROUT value may be required in order
to preserve the accuracy of the output. As an example, if
the input impedance of the driven circuit is 100 times ROUT,
then the accuracy of VOUT will be reduced by 1% since:
VI
RR
OUT
IN DRIVEN
OUT
IN DRIVEN
=
+
=
()
IIR
IR
OUT
.
100
101
099
=
Error Sources
The current sense system uses an amplier and resistors
to apply gain and level shift the result. The output is then
dependent on the characteristics of the amplier, such as
gain and input offset, as well as resistor matching.
Ideally, the circuit output is:
VV
R
VR
I
OUT
SENSE
OUT
IN
SENSE
==
;
In this case, the only error is due to resistor mismatch,
which provides an error in gain only. However, offset volt-
age and bias current cause additional errors.
Figure 3. Shunt Diode Limits Maximum Input Voltage to Allow
Better Low Input Resolution Without Overranging
Figure 2. Kelvin Input Connection Preserves Accuracy with
Large Load Currents
Selection of External Input Resistor, RIN
RIN should be chosen to allow the required resolution
while limiting the output current to 1mA. In addition, the
maximum value for RIN is 500Ω. By setting RIN such that
the largest expected sense voltage gives IOUT = 1mA, then
the maximum output dynamic range is available. Output
dynamic range is limited by both the maximum allowed
output current and the maximum allowed output voltage,
as well as the minimum practical output signal. If less
dynamic range is required, then RIN can be increased
accordingly, reducing the maximum output current and
power dissipation. If low sense currents must be resolved
accurately in a system that has a very wide dynamic range,
a smaller RIN than the maximum current spec allows may
be used if the maximum current is limited in another way,
such as with a Schottky diode across RSENSE (Figure 3).
This will reduce the high current measurement accuracy
by limiting the result, while increasing the low current
measurement resolution.
LT6106
ROUT
VOUT
6106 F02
RIN
V+
LOAD
RSENSE
–
+
V+
V–
OUT
–IN
+IN
V+
LOAD
DSENSE
6106 F03
RSENSE
相關PDF資料 |
PDF描述 |
|---|---|
| SBH11-PBPC-D07-RA-BK | CONN HEADR 2.54MM 14POS GOLD R/A |
| 0070.1781.A2 | VARISTOR 17V 20MM RADIAL |
| 68602-120HLF | CONN HEADER 20POS .100 STR 30AU |
| 0070.1481.A2 | VARISTOR 14V 20MM RADIAL |
| ADM4073FWRJZ-REEL7 | IC AMP CS 1.8MHZ SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT6106HS5#PBF | 制造商:Linear Technology 功能描述:SP Amp Current Sense Amp Single 36V 5-Pin TSOT-23 制造商:Linear Technology 功能描述:SP Amp Current Sense Amp Single 36V 5-Pin TSOT-23 Bulk 制造商:Linear Technology 功能描述:AMP CURRENT SENSE 36V TSOT-23-5 制造商:Linear Technology 功能描述:IC OP-AMP 200kHz 5-SOT-23 制造商:Linear Technology 功能描述:AMP, CURRENT SENSE, 36V, TSOT-23-5 制造商:Linear Technology 功能描述:IC, OP-AMP, 200kHz, 5-SOT-23; Op Amp Type:High Current; No. of Amplifiers:1; Supply Voltage Range:2.7V to 36V; Amplifier Case Style:SOT-23; No. of Pins:5; Bandwidth:200kHz; Operating Temperature Min:-40C; MSL:MSL 1 - Unlimited ;RoHS Compliant: Yes |
| LT6106HS5#TRM | 制造商:Linear Technology 功能描述: |
| LT6106HS5#TRMPBF | 功能描述:IC AMP CURRENT SENSE TSOT23-5 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| LT6106HS5#TRPBF | 功能描述:IC AMP CURRENT SENSE TSOT23-5 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 |
| LT6106HS5TRMPBF | 制造商:Linear Technology 功能描述:36V High-Side Current Sense TSOT23-5 |
發布緊急采購，3分鐘左右您將得到回復。