參數資料
型號： LT6350HMS8#PBF
廠商： Linear Technology
文件頁數： 9/28頁
文件大?。?/td> 0K
描述： IC DIFF CONVERT/ADC DRIVER 8MSOP
標準包裝： 50
類型： ADC 驅動器
應用： 數據采集
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 管件
配用： DC1783A-H-ND - BOARD SAR ADC LTC2376-18
DC1783A-G-ND - BOARD SAR ADC LTC2377-18
DC1783A-F-ND - BOARD SAR ADC LTC2378-18
DC1783A-E-ND - BOARD SAR ADC LTC2379-18
DC1783A-D-ND - BOARD SAR ADC LTC2376-16
DC1783A-C-ND - BOARD SAR ADC LTC2377-16
DC1783A-B-ND - BOARD SAR ADC LTC2378-16
DC1783A-A-ND - BOARD SAR ADC LTC2380-16
DC1500A-C-ND - BOARD SAR ADC LTC2391-16
DC1500A-B-ND - BOARD SAR ADC LTC2392-16
LT6350
17
6350fc
For more information www.linear.com/LT6350
applicaTions inForMaTion
The capacitance serves to provide the bulk of the charge
during the sampling process, while the two resistors at the
outputs of the LT6350 are used to dampen and attenuate
any charge injected by the ADC. The RC filter can also be
used to the additional benefit of band limiting broadband
output noise. See the Noise Considerations section for
more information.
The selection of the RC time constant depends on the ADC;
but generally, longer time constants will improve SNR at
the expense of longer settling time. Excessive settling time
can introduce gain errors and can cause distortion if the
filter components are not perfectly linear. Note also that
too small of a resistor will not properly dampen the load
transient of the sampling process, prolonging the time
required for settling. 16-bit applications typically require
a minimum settling time of eleven RC time constants of
a first order filter.
Note that the filter’s series resistance also serves to
decouple the LT6350 outputs from load capacitance. The
outputs of the LT6350 are designed to drive a maximum
of 40pF to ground or 20pF differentially; higher values
of filter capacitor should always be decoupled with filter
resistors of at least 25Ω.
High quality resistors and capacitors should be used in
the RC filter since these components can contribute to
distortion. For lowest distortion, choose capacitors with
a high quality dielectric, such as a C0G multilayer ceramic
capacitor. Metal film surface mount resistors are more
linear than carbon types.
SETTING THE OUTPUT COMMON MODE VOLTAGE
The output common mode voltage is set by the voltage
applied to pin +IN2 in accordance with Equation (3). The
usable output common mode range is determined by the
input common mode range of the inverting op amp and
is from V– + 1.5V to V+.
In single supply applications, the optimal common mode
input range to the ADC is often determined by the ADC’s
reference. If the ADC has an output pin for setting the input
common mode voltage, it can be directly tied to the +IN2
pin, as long as it is capable of providing the input current
into +IN2 as listed in the Electrical Characteristics Table.
Alternatively, +IN2 may be driven by an external precision
reference such as the LT1790.
For lowest offset, the +IN2 pin should see 499Ω of driving
resistance in all applications (see Offset Considerations).
If the driving resistance is nominally less than 499Ω,
additional resistance can be added to make up the
difference. The resistor noise bandwidth can be reduced
by bypassing the +IN2 pin to the ground plane with a
chip ceramic capacitor of at least 0.1F (see the Typical
Application on the front page). The bypass capacitance
also helps prevent AC signals on this pin from being
inadvertently converted to differential signals.
SHDN
If the SHDN pin (Pin 7), is pulled low within 300mV of the
negative supply rail, the LT6350 will power down. The pin
is connected through a diode to an internal current source
of 20A. When pulled below the shutdown threshold, the
20A current will flow from the pin. If the pin is left open
or pulled high (above V– + 2V), the part will enter normal
active operation, and the current into the pin will be very
small due to the reverse-biased diode.
相關PDF資料
PDF描述
LT6350HDD#PBF IC DIFF CONVERT/ADC DRIVER 8-DFN
VI-2TN-IV-F3 CONVERTER MOD DC/DC 18.5V 150W
VI-2TM-MW-B1 CONVERTER MOD DC/DC 10V 100W
VI-2TN-IV-F2 CONVERTER MOD DC/DC 18.5V 150W
VI-2TL-IV-F4 CONVERTER MOD DC/DC 28V 150W
相關代理商/技術參數
參數描述
LT6350HMS8TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise Single-Ended to Differential Converter/ADC Driver
LT6350IDD#PBF 功能描述:IC DIFF CONVERT/ADC DRIVER 8-DFN RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變?cè)鲆娣糯笃?應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤
LT6350IDD#TRPBF 功能描述:IC DIFF CONVERT/ADC DRIVER 8-DFN RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變?cè)鲆娣糯笃?應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤
LT6350IDDPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise Single-Ended to Differential Converter/ADC Driver
LT6350IDDTRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise Single-Ended to Differential Converter/ADC Driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*