參數資料
型號： LTAEY
廠商： Linear Integrated Systems
英文描述： Differential Input 16-Bit No Latency DS ADC
中文描述： 差分輸入16位ADC的無延遲局副局長
文件頁數： 17/28頁
文件大小： 298K
代理商： LTAEY
LTC2433-1
17
24331fa
disabled. Hence, SCK remains LOW. On the next falling
edge of CS, the device is switched to the external SCK
timing mode. By adding an external 10k pull-up resistor to
SCK, this pin goes HIGH once the external driver goes
Hi-Z. On the next CS falling edge, the device will remain in
the internal SCK timing mode.
A similar situation may occur during the sleep state when
CS is pulsed HIGH-LOW-HIGH in order to test the
conversion status. If the device is in the sleep state (EOC
= 0), SCK will go LOW. Once CS goes HIGH (within the time
period defined above as t
EOCtest
), the internal pull-up is
activated. For a heavy capacitive load on the SCK pin, the
internal pull-up may not be adequate to return SCK to a
HIGH level before CS goes low again. This is not a concern
under normal conditions where CS remains LOW after
detecting EOC = 0. This situation is easily overcome by
adding an external 10k pull-up resistor to the SCK pin.
Internal Serial Clock, 2-Wire I/O,
Continuous Conversion
This timing mode uses a 2-wire, all output (SCK and SDO)
interface. The conversion result is shifted out of the device
by an internally generated serial clock (SCK) signal, see
Figure 11. CS may be permanently tied to ground, simpli-
fying the user interface or isolation barrier.
The internal serial clock mode is selected at the end of the
power-on reset (POR) cycle. The POR cycle is concluded
approximately 1ms after V
CC
exceeds 2V. An internal weak
pull-up is active during the POR cycle; therefore, the
internal serial clock timing mode is automatically selected
if SCK is not externally driven LOW (if SCK is loaded such
that the internal pull-up cannot pull the pin HIGH, the
external SCK mode will be selected).
Figure 10. Internal Serial Clock, Reduced Data Output Length
SDO
SCK
(INTERNAL)
CS
>t
EOCtest
MSB
SIG
“O”
BIT 2
TEST EOC
BIT 14
BIT 13
BIT 15
BIT 16
BIT 17
EOC
BIT 18
EOC
BIT 0
DATA OUTPUT
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Hi-Z
DATA
OUTPUT
CONVERSION
CONVERSION
SLEEP
24331 F10
<t
EOCtest
V
CC
10k
TEST EOC
(OPTIONAL)
TEST EOC
SLEEP
SLEEP
= EXTERNAL CLOCK SOURCE
= INTERNAL OSC/SIMULTANEOUS
50Hz/60Hz REJECTION
V
CC
F
O
REF
+
REF
–
SCK
IN
+
IN
–
GND
SDO
CS
1
10
2
3
9
4
5
6
8
7
REFERENCE
VOLTAGE
0.1V TO V
CC
ANALOG INPUT RANGE
–0.5V
REF
TO 0.5V
REF
1
μ
F
2.7V TO 5.5V
LTC2433-1
3-WIRE
SPI INTERFACE
APPLICATIOU
W
U
U
相關PDF資料
PDF描述
LTAEZ Differential Input 16-Bit No Latency DS ADC
LTC2433-1 Differential Input 16-Bit No Latency DS ADC
LTC2433-1CMS Differential Input 16-Bit No Latency DS ADC
LTC2433-1IMS Differential Input 16-Bit No Latency DS ADC
LTC1043CS Dual Precision Intrumentation Switched-Capacitor Building Block
相關代理商/技術參數
參數描述
LTAEZ 制造商:LINEAR 制造商全稱:LINEAR 功能描述:Differential Input 16-Bit No Latency DS ADC
LTAGL 制造商:LINER 制造商全稱:Linear Technology 功能描述:100mA, Low Voltage, Very Low Dropout Linear Regulator
LT-ALTO350-C 制造商:LED TEAM 功能描述:DRIVER 3CH DMX FOR RGB LED 350MA
LT-ALTO700-C 制造商:LED TEAM 功能描述:LED DRIVER DC-DC CC 0.7A 制造商:LED TEAM 功能描述:LED DRIVER, DC-DC, CC, 0.7A 制造商:LED TEAM 功能描述:LED DRIVER, DC-DC, CC, 0.7A, Product Range:LED TEAM - ALTO700 Series, Input Volt 制造商:LED TEAM 功能描述:LED DRIVER, DC-DC, CC, 0.7A, Product Range:LED TEAM - ALTO700 Series, Input Voltage Min:24V, Input Voltage Max:32V, Output Current:700mA, Output Power Max:45W, DC / DC Converter Mounting:Panel, Dimming Control Type:PWM, Depth:22mm, , RoHS Compliant: Yes
LTALX 制造商:Apex Tool Group 功能描述:TIP,BENT CHISEL,30 DEG,1.6MM,WP80
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*