- 您現在的位置：買賣IC網 > PDF目錄377732 > LTC1142HV-ADJ (Linear Technology Corporation) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LTC1142HV-ADJ |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 抗輻射高效，5安培開關穩壓器 |
| 文件頁數： | 11/20頁 |
| 文件大小： | 401K |
| 代理商： | LTC1142HV-ADJ |
11
LTC1142/LTC1142L/LTC1142HV
APPLICATIU
eased at the expense of efficiency. If too small an inductor
is used, the inductor current will decrease past zero and
change polarity. A consequence of this is that the LTC1142
may not enter Burst Mode
operation and efficiency will be
severely degraded at low currents.
W
U
U
Inductor Core Selection
Once the minimum value for L is known, the type of
inductor must be selected. The highest efficiency will be
obtained using ferrite, molypermalloy (MPP), or Kool M
μ
cores. Lower cost powdered iron cores provide suitable
performance, but cut efficiency by 3% to 7%. Actual core
loss is independent of core size for a fixed inductor value,
but it is very dependent on inductance selected. As induc-
tance increases, core losses go down. Unfortunately,
increased inductance requires more turns of wire and
therefore copper losses will increase.
Ferrite designs have very low core loss, so design goals
can concentrate on copper loss and preventing saturation.
Ferrite core material saturates “hard,” which means that
inductance collapses abruptly when the peak design cur-
rent is exceeded. This results in an abrupt increase in
inductor ripple current and consequent output voltage
ripple which can cause Burst Mode
operation to be falsely
triggered. Do not allow the core to saturate!
Kool M
μ
(from Magnetics, Inc.) is a very good, low loss
core material for toroids with a “soft” saturation charac-
teristic. Molypermalloy is slightly more efficient at high
(>200kHz) switching frequencies, but it is quite a bit more
expensive. Toroids are very space efficient, especially
when you can use several layers of wire. Because they
generally lack a bobbin, mounting is more difficult. How-
ever, new designs for surface mount are available from
Coiltronics and Beckman Industrial Corporation which do
not increase the height significantly.
Power MOSFET and D1, D2 Selection
Two external power MOSFETs must be selected for use with
each section of the LTC1142: a P-channel MOSFET for the
main switch, and an N-channel MOSFET for the synchronous
switch. The main selection criteria for the power MOSFETs
are the threshold voltage V
GS(TH)
and on- resistance R
DS(ON)
.
Kool M
μ
is a registered trademark of Magnetics, Inc.
The minimum input voltage determines whether standard
threshold or logic-level threshold MOSFETs must be
used. For V
IN
> 8V, standard threshold MOSFETs
(
V
GS(TH)
< 4V) may be used. If V
IN
is expected to drop
below 8V, logic-level threshold MOSFETs (V
GS(TH)
<
2.5V) are strongly recommended. When logic-level
MOSFETs are used, the LTC1142 supply voltage must
be less than the absolute maximum V
GS
ratings for the
MOSFETs.
The maximum output current I
MAX
determines the R
DS(ON)
requirement for the two MOSFETs. When the LTC1142 is
operating in continuous mode, the simplifying assump-
tion can be made that one of the two MOSFETs is always
conducting the average load current. The duty cycles for
the two MOSFETs are given by:
P-Ch Duty Cycle=V
V
N-Ch Duty Cycle=V
V
V
OUT
IN
IN
OUT
IN
From the duty cycles the required R
DS(ON)
for each
MOSFET can be derived:
P-Ch R
=
V
V
N-Ch R
=
V
)
×
DS(ON)
IN
OUT
DS(ON)
IN
×
2
×
×
+
(
×
I
MAX
)
(
×
+
(
)
P
I
P
V
V
P
MAX
P
N
IN
OUT
N
2
1
1
δ
δ
where P
P
and P
N
are the allowable power dissipations and
δ
P
and
δ
N
are the temperature dependencies of R
DS(ON)
.
P
P
and P
N
will be determined by efficiency and/or thermal
requirements (see Efficiency Considerations). (1 +
δ
) is
generally given for a MOSFET in the form of a normalized
R
DS(ON)
vs Temperature curve, but
δ
= 0.007/
°
C can be
used as an approximation for low voltage MOSFETs.
The Schottky diodes D1 and D2 shown in Figure 1 only
conduct during the dead-time between the conduction of
the respective power MOSFETs. The sole purpose of D1
and D2 is to prevent the body diode of the N-channel
MOSFET from turning on and storing charge during the
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1142HVCG | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1142HVCG-ADJ | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1143CS | Enclosures; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes RoHS Compliant: Yes |
| LTC1143L-ADJ | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1143LCS-ADJ | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1142HVCG | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1142HVCG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1142HVCG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1142HVCG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1142HVCG-ADJ | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。