- 您現在的位置：買賣IC網 > PDF目錄10282 > LTC1298IS8#TR (Linear Technology)IC ADC 12BIT SAMPL MCRPWR 8SOIC PDF資料下載
參數資料
| 型號： | LTC1298IS8#TR |
| 廠商： | Linear Technology |
| 文件頁數： | 6/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SAMPL MCRPWR 8SOIC |
| 標準包裝： | 2,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 11.1k |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 1.8mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，單極 |
14
LTC1286/LTC1298
Figure 5. Shutdown current with CS high is 1nA typically,
regardless of the clock. Shutdown current with CS = ground
varies from 1
A at 1kHz to 35A at 200kHz.
APPLICATION INFORMATION
WU
U
Clock Frequency
The maximum recommended clock frequency is 200kHz
for the LTC1286/LTC1298 running off a 5V supply. With
the supply voltage changing, the maximum clock fre-
quency for the devices also changes (see the typical curve
of Maximum Clock Rate vs Supply Voltage). If the maxi-
mum clock frequency is used, care must be taken to
ensure that the device converts correctly.
Mixed Supplies
It is possible to have a microprocessor running off a 5V
supply and communicate with the LTC1286 operating on
a 9V supply. The requirement to achieve this is that the
outputs of CS and CLK from the MPU have to be able to trip
the equivalent inputs of the LTC1286 and the output of
DOUT from the LTC1286 must be able to toggle the
equivalent input of the MPU (see typical curve of Digital
Input Logic Threshold vs Supply Voltage). With the
LTC1286 operating on a 9V supply, the output of DOUT may
go between 0V and 9V. The 9V output may damage the
MPU running off a 5V supply. The way to get around this
possibility is to have a resistor divider on DOUT (Figure 6)
and connect the center point to the MPU input. It should
be noted that to get full shutdown, the CS input of the
LTC1286 must be driven to the VCC voltage to keep the CS
input buffer from drawing current. An alternative is to
leave CS low after a conversion, clock data until DOUT
outputs zeros, and then stop the clock low.
DOUT Loading
Capacitive loading on the digital output can increase power
consumption. A 100pF capacitor on the DOUT pin can add
more than 50
A to the supply current at a 200kHz clock
frequency. An extra 50
A or so of current goes into
charging and discharging the load capacitor. The same
goes for digital lines driven at a high frequency by any logic.
The C
× V × f currents must be evaluated and the trouble-
some ones minimized.
OPERATING ON OTHER THAN 5V SUPPLIES (LTC1286)
The LTC1286 operates from 4.5V to 9V supplies and the
LTC1298 operates from a 5V supply. To operate the LTC1286
on other than 5V supplies a few things must be kept in
mind.
Input Logic Levels
The input logic levels of CS, CLK and DIN are made to meet
TTL on a 5V supply. When the supply voltage varies, the
input logic levels also change. For the LTC1286 to sample
and convert correctly, the digital inputs have to be in the
proper logical low and high levels relative to the operating
supply voltage (see typical curve of Digital Input Logic
Threshold vs Supply Voltage). If achieving micropower
consumption is desirable, the digital inputs must go rail-to-
rail between supply voltage and ground (see ACHIEVING
MICROPOWER PERFORMANCE section).
FREQUENCY (kHz)
1
0.002
SUPPLY
CURRENT
(A)
5
1
0
15
20
25
35
20
100
140
LT1286/98 G01
10
30
80
180 200
40 60
120
160
CS = 0
(AFTER CONVERSION)
TA = 25°C
VCC = VREF = 5V
CS = VCC
+IN
–IN
GND
VCC
CLK
DOUT
VREF
50k
5V
4.7
F
MPU
(e.g. 8051)
5V
P1.4
P1.3
P1.2
LTC1286/98 F06
DIFFERENTIAL INPUTS
COMMON-MODE RANGE
0V TO 5V
9V
LTC1286
CS
Figure 6. Interfacing a 9V Powered LTC1286 to a 5V System
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26MH21SALC | CONN HSG PLUG 21POS STRGHT SCKT |
| LTC1286IS8#TRPBF | IC CONV A/D SAMPLING 12BIT 8SOIC |
| D38999/26MH21BN | CONN HSG PLUG 21POS STRGHT SCKT |
| D38999/26MD97PNLC | CONN HSG PLUG 12POS STRGHT PINS |
| VE-2NT-MY | CONVERTER MOD DC/DC 6.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1314CS | 功能描述:IC PCMCIA SWITCHNG MATRIX 14SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源分配開關 系列:- 特色產品:XRP252 Switches 標準包裝:1 系列:- 類型:高端開關 輸出數:2 Rds（開）:140 毫歐 內部開關:是 電流限制:1.15A 輸入電壓:1.75 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN（3x3） 包裝:Digi-Reel® 其它名稱:1016-1691-6 |
| LTC1314CS#PBF | 功能描述:IC PCMCIA SWITCHNG MATRIX 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源分配開關 系列:- 特色產品:XRP252 Switches 標準包裝:1 系列:- 類型:高端開關 輸出數:2 Rds（開）:140 毫歐 內部開關:是 電流限制:1.15A 輸入電壓:1.75 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN（3x3） 包裝:Digi-Reel® 其它名稱:1016-1691-6 |
| LTC1314CS#TR | 功能描述:IC SW MATRIX PCMCIA SGL 14SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源分配開關 系列:- 特色產品:XRP252 Switches 標準包裝:1 系列:- 類型:高端開關 輸出數:2 Rds（開）:140 毫歐 內部開關:是 電流限制:1.15A 輸入電壓:1.75 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN（3x3） 包裝:Digi-Reel® 其它名稱:1016-1691-6 |
| LTC1314CS#TRPBF | 功能描述:IC PCMCIA SWITCHNG MATRIX 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源分配開關 系列:- 特色產品:XRP252 Switches 標準包裝:1 系列:- 類型:高端開關 輸出數:2 Rds（開）:140 毫歐 內部開關:是 電流限制:1.15A 輸入電壓:1.75 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN（3x3） 包裝:Digi-Reel® 其它名稱:1016-1691-6 |
| LTC1315CG#PBF | 功能描述:IC PCMCIA SWITCHNG MATRIX 24SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源分配開關 系列:- 標準包裝:80 系列:- 類型:USB 開關 輸出數:2 Rds（開）:135 毫歐 內部開關:是 電流限制:1.5A 輸入電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-MSOP-PowerPad 包裝:管件 配用:TPS2066-1EVM-296-ND - TPS2066-1EVM-296 |
發布緊急采購，3分鐘左右您將得到回復。