- 您現在的位置：買賣IC網 > PDF目錄377745 > LTC1403 (Linear Technology Corporation) Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown PDF資料下載
參數資料
| 型號： | LTC1403 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown |
| 中文描述： | 串行12-Bit/14-Bit，2.8Msps采樣ADC，帶有關斷 |
| 文件頁數： | 12/20頁 |
| 文件大?。?/td> | 323K |
| 代理商： | LTC1403 |
12
LTC1403/LTC1403A
1403af
Board Layout and Bypassing
Wire wrap boards are not recommended for high resolu-
tion and/or high speed A/D converters. To obtain the best
performance from the LTC1403/LTC1403A, a printed cir-
cuit board with ground plane is required. Layout for the
printed circuit board should ensure that digital and analog
signal lines are separated as much as possible. In particu-
lar, care should be taken not to run any digital track
alongside an analog signal track. If optimum phase match
between the inputs is desired, the length of the two input
wires should be kept matched.
High quality tantalum and ceramic bypass capacitors
should be used at the V
DD
and V
REF
pins as shown in the
Block Diagram on the first page of this data sheet. For
Figure 5. Recommended Layout
optimum performance, a 10
μ
F surface mount AVX capaci-
tor with a 0.1
μ
F ceramic is recommended for the V
DD
and
V
REF
pins. Alternatively, 10
μ
F ceramic chip capacitors
such as Murata GRM235Y5V106Z016 may be used. The
capacitors must be located as close to the pins as possible.
The traces connecting the pins and the bypass capacitors
must be kept short and should be made as wide as
possible.
Figure 5 shows the recommended system ground connec-
tions. All analog circuitry grounds should be terminated at
the LTC1403/LTC1403A GND (Pins 4, 5, 6 and exposed
pad). The ground return from the LTC1403/LTC1403A
(Pins 4, 5, 6 and exposed pad) to the power supply should
be low impedance for noise free operation. Digital circuitry
grounds must be connected to the digital supply common.
In applications where the ADC data outputs and control
signals are connected to a continuously active micropro-
cessor bus, it is possible to get errors in the conversion
results. These errors are due to feedthrough from the
microprocessor to the successive approximation com-
parator. The problem can be eliminated by forcing the
microprocessor into a Wait state during conversion or by
using three-state buffers to isolate the ADC data bus.
POWER-DOWN MODES
Upon power-up, the LTC1403/LTC1403A is initialized to
the active state and is ready for conversion. The Nap and
Sleep mode waveforms show the power-down modes for
the LTC1403/LTC1403A. The SCK and CONV inputs con-
trol the power-down modes (see Timing Diagrams). Two
rising edges at CONV, without any intervening rising
edges at SCK, put the LTC1403/LTC1403A. in Nap mode
and the power drain drops from 14mW to 6mW. The
internal reference remains powered in Nap mode. One or
more rising edges at SCK wake up the LTC1403/LTC1403A
for service very quickly, and CONV can start an accurate
conversion within a clock cycle. Four rising edges at
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1403A | Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown |
| LTC1403AIMSE | Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown |
| LTC1404IS8 | Complete SO-8, 12-Bit, 600ksps ADC with Shutdown |
| LTC1404C | Complete SO-8, 12-Bit, 600ksps ADC with Shutdown |
| LTC1404CS8 | Complete SO-8, 12-Bit, 600ksps ADC with Shutdown |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1403ACMSE | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1403ACMSE#PBF | 功能描述:IC ADC 14BIT 2.8MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1403ACMSE#PBF | 制造商:Linear Technology 功能描述:ADC, 14BIT, 2.8MSPS, MSOP-10 |
| LTC1403ACMSE#TR | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1403ACMSE#TRPBF | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。