- 您現在的位置：買賣IC網 > PDF目錄377745 > LTC1403CMSE (LINEAR TECHNOLOGY CORP) Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown PDF資料下載
參數資料
| 型號： | LTC1403CMSE |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown |
| 中文描述： | 1-CH 12-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PDSO10 |
| 封裝： | PLASTIC, MSOP-10 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 323K |
| 代理商： | LTC1403CMSE |
9
LTC1403/LTC1403A
1403af
DRIVING THE ANALOG INPUT
The differential analog inputs of the LTC1403/LTC1403A are
easy to drive. The inputs may be driven differentially or as a
single-ended input (i.e., the A
IN–
input is grounded). Both
differential analog inputs, A
IN+
with A
IN–
, are sampled at the
same instant. Any unwanted signal that is common to both
inputs of each input pair will be reduced by the common mode
rejection of the sample-and-hold circuit. The inputs draw only
one small current spike while charging the sample-and-hold
capacitors at the end of conversion. During conversion, the
analog inputs draw only a small leakage current. If the source
impedance of the driving circuit is low, then the LTC1403/
LTC1403A inputs can be driven directly. As source imped-
ance increases, so will acquisition time. For minimum acqui-
sition time with high source impedance, a buffer amplifier
must be used. The main requirement is that the amplifier
driving the analog input(s) must settle after the small current
spike before the next conversion starts (settling time must be
39ns for full throughput rate). Also keep in mind while
choosing an input amplifier, the amount of noise and har-
monic distortion added by the amplifier.
CHOOSING AN INPUT AMPLIFIER
Choosing an input amplifier is easy if a few requirements are
taken into consideration. First, to limit the magnitude of the
voltage spike seen by the amplifier from charging the sam-
pling capacitor, choose an amplifier that has a low output
impedance (<100
) at the closed-loop bandwidth frequency.
For example, if an amplifier is used in a gain of 1 and has a
unity-gain bandwidth of 50MHz, then the output impedance
at 50MHz must be less than 100
. The second requirement
is that the closed-loop bandwidth must be greater than
40MHz to ensure adequate small-signal settling for full
throughput rate. If slower op amps are used, more time for
settling can be provided by increasing the time between
conversions. The best choice for an op amp to drive the
LTC1403/LTC1403A will depend on the application. Gener-
ally, applications fall into two categories: AC applications
where dynamic specifications are most critical and time
domain applications where DC accuracy and settling time are
most critical. The following list is a summary of the op amps
that are suitable for driving the LTC1403/LTC1403A. (More
detailed information is available in the Linear Technology
Databooks and on the LinearView
TM
CD-ROM.)
LTC
1566-1:
Low Noise 2.3MHz Continuous Time Low-
Pass Filter.
LT1630:
Dual 30MHz Rail-to-Rail Voltage FB Amplifier. 2.7V
to
±
15V supplies. Very high A
VOL
, 500
μ
V offset and 520ns
settling to 0.5LSB for a 4V swing. THD and noise are –93dB
to 40kHz and below 1LSB to 320kHz (A
V
= 1, 2V
P-P
into 1k
,
V
S
= 5V), making the part excellent for AC applications (to 1/
3 Nyquist) where rail-to-rail performance is desired. Quad
version is available as LT1631.
LT1632:
Dual 45MHz Rail-to-Rail Voltage FB Amplifier. 2.7V
to
±
15V supplies. Very high A
VOL
, 1.5mV offset and 400ns
settling to 0.5LSB for a 4V swing. It is suitable for applica-
tions with a single 5V supply. THD and noise are
–93dB to 40kHz and below 1LSB to 800kHz (A
V
= 1,
2V
P-P
into 1k
, V
S
= 5V), making the part excellent for AC
applications where rail-to-rail performance is desired.
Quad
version is available as LT1633.
LT1813:
Dual 100MHz 750V/
μ
s 3mA Voltage Feedback
Amplifier. 5V to
±
5V supplies. Distortion is –86dB to 100kHz
and –77dB to 1MHz with
±
5V supplies (2V
P-P
into 500
).
Excellent part for fast AC applications with
±
5Vsupplies.
LT1801:
80MHz GBWP, –75dBc at 500kHz, 2mA/Amplifier,
8.5nV/
√
Hz.
LT1806/LT1807:
325MHz GBWP, –80dBc Distortion at 5MHz,
Unity-Gain Stable, R-R In and Out, 10mA/Amplifier, 3.5nV/
√
Hz.
LT1810:
180MHz GBWP, –90dBc Distortion at 5MHz,
Unity-Gain Stable, R-R In and Out, 15mA/Amplifier, 16nV/
√
Hz.
LT1818/LT1819:
400MHz, 2500V/
μ
s,9mA, Single/Dual Volt-
age Mode Operational Amplifier.
LT6200:
165MHz GBWP, –85dBc Distortion at 1MHz, Unity-
Gain Stable, R-R In and Out, 15mA/Amplifier,
0.95nV/
√
Hz.
LT6203:
100MHz GBWP, –80dBc Distortion at 1MHz,
Unity-Gain Stable, R-R In and Out, 3mA/Amplifier,
1.9nV/
√
Hz.
LT6600-10:
Amplifier/Filter Differential In/Out with 10MHz
Cutoff.
APPLICATIU
W
U
U
LinearView is a trademark of Linear Technology Corporation.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1403 | Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown |
| LTC1403A | Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown |
| LTC1403AIMSE | Serial 12-Bit/14-Bit, 2.8Msps Sampling ADCs with Shutdown |
| LTC1404IS8 | Complete SO-8, 12-Bit, 600ksps ADC with Shutdown |
| LTC1404C | Complete SO-8, 12-Bit, 600ksps ADC with Shutdown |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1403CMSE#PBF | 功能描述:IC ADC 12BIT 2.8MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1403CMSE#TR | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1403CMSE#TRPBF | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1403CMSE-1 | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1403CMSE-1#PBF | 功能描述:IC ADC 12BIT 2.8MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。