參數資料
型號： LTC1407CMSE-1
廠商： Linear Technology
文件頁數： 6/26頁
文件大小： 0K
描述： IC ADC 12BIT 3MSPS SAMPLE 10MSOP
標準包裝： 50
位數： 12
采樣率（每秒）： 3M
數據接口： 串行，SPI?
轉換器數目： 1
功率耗散（最大）： 14mW
電壓電源： 單電源
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤
供應商設備封裝： 10-MSOP 裸露焊盤
包裝： 管件
輸入數目和類型： 4 個單端，單極；2 個差分，單極
配用： DC1082A-B-ND - BOARD SAR ADC LTC1407A
DC1082A-A-ND - BOARD SAR ADC LTC1407A-1
LTC1407-1/LTC1407A-1
14
14071fb
APPLICATIONS INFORMATION
LT1818/LT1819: 400MHz, 2500V/μs, 9mA, Single/Dual
Voltage Mode Operational Amplier.
LT6200: 165MHz GBWP, –85dBc distortion at 1MHz,
unity-gain stable, rail-to-rail in and out, 15mA/amplier,
0.95nV/√Hz.
LT6203: 100MHz GBWP, –80dBc distortion at 1MHz,
unity-gain stable, rail-to-rail in and out, 3mA/amplier,
1.9nV/√Hz.
LT6600: Amplier/Filter Differential In/Out with 10MHz
Cutoff.
INPUT FILTERING AND SOURCE IMPEDANCE
The noise and the distortion of the input amplier and
other circuitry must be considered since they will add
to the LTC1407-1/LTC1407A-1 noise and distortion. The
small-signal bandwidth of the sample-and-hold circuit is
50MHz. Any noise or distortion products that are pres-
ent at the analog inputs will be summed over this entire
bandwidth. Noisy input circuitry should be ltered prior
to the analog inputs to minimize noise. A simple 1-pole
RC lter is sufcient for many applications. For example,
Figure 1 shows a 47pF capacitor from CHO+ to ground
and a 51Ω source resistor to limit the net input bandwidth
to 30MHz. The 47pF capacitor also acts as a charge
reservoir for the input sample-and-hold and isolates the
ADC input from sampling-glitch sensitive circuitry. High
quality capacitors and resistors should be used since these
Figure 1. RC Input Filter
components can add distortion. NPO and silvermica type
dielectric capacitors have excellent linearity. Carbon surface
mount resistors can generate distortion from self heating
and from damage that may occur during soldering. Metal
lm surface mount resistors are much less susceptible to
both problems. When high amplitude unwanted signals
are close in frequency to the desired signal frequency a
multiple pole lter is required.
High external source resistance, combined with 13pF
of input capacitance, will reduce the rated 50MHz input
bandwidth and increase acquisition time beyond 39ns.
INPUT RANGE
The analog inputs of the LTC1407-1/LTC1407A-1 may be
driven fully differentially with a single supply. Either input
may swing up to 3V, provided the differential swing is no
greater than 1.25V. In the valid input range, each input of
each channel is always up to ±1.25V away from the other
input of each channel. The –1.25V to 1.25V range is also
ideally suited for AC-coupled signals in single supply
applications. Figure 2 shows how to AC-couple signals
in a single supply system without needing a mid-supply
1.5V DC external reference. The DC common mode level
is supplied by the previous stage that is already bounded
by single supply voltage of the system. The common
mode range of the inputs extends from ground to the
supply voltage VDD. If the difference between the CH0+
and CH0– inputs or the CH1+ and CH1– inputs exceeds
1.25V, the output code will stay xed at zero and all ones,
and if this difference goes below –1.25V, the output code
will stay xed at one and all zeros.
Figure 2. AC Coupling of AC Signals with 1kHz Low Cut
LTC1407-1/
LTC1407A-1
CH0+
CH0–
VREF
GND
14071 F01
1
2
11
3
10μF
47pF*
51Ω*
CH1+
CH1–
4
5
47pF*
*TIGHT TOLERANCE REQUIRED TO AVOID
APERTURE SKEW DEGRADATION
51Ω*
ANALOG
INPUT
ANALOG
INPUT
VCM
1.5V DC
VCM
1.5V DC
+
CHO+
4.09V
C4
10μF
14071 F02
R2
1.6k
C2
1μF
C1
1μF
C1, C2: FILM TYPE
C3: COG TYPE
C4: CERAMIC BYPASS
R1
1.6k
1
2
3
LTC1407-1/
LTC1407A-1
CHO–
VREF
R3
51Ω
C3
56pF
VIN
相關PDF資料
PDF描述
MS27467T15B5PA CONN PLUG 5POS STRAIGHT W/PINS
VE-B3J-IX-B1 CONVERTER MOD DC/DC 36V 75W
VE-26M-IU-S CONVERTER MOD DC/DC 10V 200W
D38999/20JD97PNLC CONN HSG RCPT 12POS WALL MT PINS
VE-26L-IU-S CONVERTER MOD DC/DC 28V 200W
相關代理商/技術參數
參數描述
LTC1407CMSE-1#PBF 功能描述:IC ADC 12BIT 3MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC1407CMSE-1#TR 功能描述:IC ADC 12BIT 3MSPS SAMPLE 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC1407CMSE-1#TRPBF 功能描述:IC ADC 12BIT 3MSPS SAMPLE 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC1407HMSE#PBF 功能描述:IC ADC 12BIT 3MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC1407HMSE#TRPBF 功能描述:IC ADC 12BIT 3MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*