- 您現在的位置：買賣IC網 > PDF目錄2003 > LTC1408IUH-12#TRPBF (Linear Technology)IC ADC 12BIT 600KSPS 32-QFN PDF資料下載
參數資料
| 型號： | LTC1408IUH-12#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 600KSPS 32-QFN |
| 標準包裝： | 2,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 600k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 15mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 12 個單端，單極；12 個單端，雙極；6 個差分，單極；6 個差分，雙極 |
| 配用： | DC887A-ND - BOARD SAR ADC LTC1408 |
16
LTC1408-12
140812f
APPLICATIO S I FOR ATIO
WU
UU
POWER-DOWN MODES
Upon power-up, the LTC1408-12 is initialized to the
active state and is ready for conversion. The Nap and Sleep
mode waveforms show the power down modes for the
LTC1408-12. The SCK and CONV inputs control the power
down modes (see Timing Diagrams). Two rising edges at
CONV, without any intervening rising edges at SCK, put
the LTC1408-12 in Nap mode and the power consumption
drops from 15mW to 3.3mW. The internal reference
remains powered in Nap mode. One or more rising edges
at SCK wake up the LTC1408-12 very quickly and CONV
can start an accurate conversion within a clock cycle. Four
rising edges at CONV, without any intervening rising
edges at SCK, put the LTC1408-12 in Sleep mode and the
power consumption drops from 15mW to 6
W. One or
more rising edges at SCK wake up the LTC1408-12 for
operation. The internal reference (VREF ) takes 2ms to slew
and settle with a 10
F load. Using sleep mode more
frequently compromises the accuracy of the output data.
Note that for slower conversion rates, the Nap and Sleep
modes can be used for substantial reductions in power
consumption.
DIGITAL INTERFACE
The LTC1408-12 has a 3-wire SPI (Serial Peripheral Inter-
face) interface. The SCK and CONV inputs and SDO output
implement this interface. The SCK and CONV inputs
accept swings from 3V logic and are TTL compatible, if the
logic swing does not exceed VDD. A detailed description of
the three serial port signals follows:
Conversion Start Input (CONV)
The rising edge of CONV starts a conversion, but subse-
quent rising edges at CONV are ignored by the LTC1408-12
until the following 96 SCK rising edges have occurred. The
duty cycle of CONV can be arbitrarily chosen to be used as
a frame sync signal for the processor serial port. A simple
approach to generate CONV is to create a pulse that is one
SCK wide to drive the LTC1408-12 and then buffer this
signal to drive the frame sync input of the processor
serial port. It is good practice to drive the LTC1408-12
CONV input first to avoid digital noise interference during
the sample-to-hold transition triggered by CONV at the
start of conversion. It is also good practice to keep the
width of the low portion of the CONV signal greater than
15ns to avoid introducing glitches in the front end of the
ADC just before the sample-and-hold goes into Hold mode
at the rising edge of CONV.
Minimizing Jitter on the CONV Input
In high speed applications where high amplitude sine
waves above 100kHz are sampled, the CONV signal must
have as little jitter as possible (10ps or less). The square
wave output of a common crystal clock module usually
meets this requirement. The challenge is to generate a
CONV signal from this crystal clock without jitter corrup-
tion from other digital circuits in the system. A clock
divider and any gates in the signal path from the crystal
clock to the CONV input should not share the same
integrated circuit with other parts of the system. The SCK
and CONV inputs should be driven first, with digital buffers
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1408IUH#TRPBF | IC ADC 14BIT 600KSPS 32-QFN |
| LTC1409IG#TR | IC ADC 12BIT 800KSPS SMPL 28SSOP |
| LTC1410IG#TR | IC ADC 12BIT 1.25MSPS SMP 28SSOP |
| LTC1411IG#TRPBF | IC A/D CONV 14BIT 2.5MSPS 36SSOP |
| LTC1412IG#TR | IC ADC 12BIT 3MSPS SAMPLE 28SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1409CG | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1409CG#PBF | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1409CG#TR | 功能描述:IC ADC 12BIT 800KSPS SMPL 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1409CG#TRPBF | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1409CSW | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。