- 您現在的位置：買賣IC網 > PDF目錄377753 > LTC1553CG (LINEAR TECHNOLOGY CORP) 5-Bit Programmable Synchronous Switching Regulator Controller for Pentium II Processor PDF資料下載
參數資料
| 型號： | LTC1553CG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 5-Bit Programmable Synchronous Switching Regulator Controller for Pentium II Processor |
| 中文描述： | 19 A SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-20 |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 399K |
| 代理商： | LTC1553CG |
11
LTC1553
APPLICATIO
S I
FOR
ATIO
U
Soft Start and Current Limit
The LTC1553 includes a soft start circuit which is used for
initial start-up and during current limit operation. The SS
pin requires an external capacitor to GND with the value
determined by the required soft start time. An internal
10
μ
A current source is included to charge the external SS
capacitor. During start-up, the COMP pin is clamped to a
diode drop above the voltage at the SS pin. This prevents
the error amplifier, ERR, from forcing the loop to maxi-
mum duty cycle. The LTC1553 will begin to operate at low
duty cycle as the SS pin rises above about 1.2V (V
COMP
≈
1.8V). As SS continues to rise, Q
SS
turns off and the error
amplifier begins to regulate the output. The MIN compara-
tor is disabled when soft start is active to prevent it from
overriding the soft start function.
The LTC1553 includes yet another feedback loop to con-
trol operation in current limit. Just before every falling
edge of G1, the current comparator, CC, samples and
holds the voltage drop measured across the external
MOSFET, Q1, at the I
FB
pin. Note that when V
IN
= 12V, the
I
FB
pin requires an external Zener to GND to prevent
voltage transients at the switching node between Q1 and
Q2 from damaging internal structures. CC compares the
voltage at I
FB
to the voltage at the I
MAX
pin. As the peak
current rises, the measured voltage across Q1 increases
due to the drop across the R
DS(ON)
of Q1. When the voltage
at I
FB
drops below I
MAX
, indicating that Q1’s drain current
has exceeded the maximum level, CC starts to pull current
out of the external soft start capacitor, cutting the duty
cycle and controlling the output current level. The CC
comparator pulls current out of the SS pin in proportion to
the voltage difference between I
FB
and I
MAX
. Under minor
overload conditions, the SS pin will fall gradually, creating
a time delay before current limit takes effect. Very short,
mild overloads may not affect the output voltage at all.
More significant overload conditions will allow the SS pin
to reach a steady state, and the output will remain at a
reduced voltage until the overload is removed. Serious
overloads will generate a large overdrive at CC, allowing it
to pull SS down quickly and preventing damage to the
output components.
W
U
U
By using the R
DS(ON)
of Q1 to measure the output current,
the current limiting circuit eliminates an expensive dis-
crete sense resistor that would otherwise be required. This
helps minimize the number of components in the high
current path. Due to switching noise and variation of
R
DS(ON)
, the actual current limit trip point is not highly
accurate. The current limiting circuitry is primarily meant
to prevent damage to the power supply circuitry during
fault conditions. The exact current level where the limiting
circuit begins to take effect will vary from unit to unit as the
R
DS(ON)
of Q1 varies.
For a given current limit level, the external resistor from
I
MAX
to V
IN
can be determined by:
=
(
R
I
R
I
IMAX
LMAX
DS O) 1
(
IMAX
)(
)
where,
I
I
I
LMAX
LOAD
RIPPLE
2
=
+
I
LOAD
= Maximum load current
I
RIPPLE
= Inductor ripple current
(
(
f
OSC
= LTC1553 oscillator frequency = 300kHz
L
O
= Inductor value
R
DS(ON)Q1
= Hot on-resistance of Q1 at I
LMAX
I
IMAX
= Internal 180
μ
A sink current at I
MAX
=
)(
)
)( )( )
V
V
V
f
L
V
IN
OUT
OUT
OSC
O
IN
Q1
180
μ
A
G1
Q2
C
IN
L
O
V
OUT
1553 F05
C
OUT
R
IMAX
V
IN
–
+
CC
G2
20
LTC1553
I
MAX
7
I
FB
8
+
+
Figure 5. Current Limit Setting
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1553CSW | Advanced,Self-Calibrating, Precision, Dual Operational Amplifier 8-SOIC -55 to 125 |
| LTC1553L | 5-Bit Programmable Synchronous Switching Regulator Controller for Pentium II Processor |
| LTC1553LCG | Advanced,Self-Calibrating, Precision, Dual Operational Amplifier 8-SOIC -40 to 125 |
| LTC1553LCSW | 5-Bit Programmable Synchronous Switching Regulator Controller for Pentium II Processor |
| LTC1556CGN | SIM Power Supply and Level Translator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1553CG#PBF | 功能描述:IC SW REG CNTRLR 5BIT PROG20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC1553CG#TR | 功能描述:IC REG SW CTRLR 5BIT PROG 20SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC1553CG#TRPBF | 功能描述:IC SW REG CNTRLR 5BIT PROG20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC1553CSW | 功能描述:IC SW REG CNTRLR 5BIT PROG20SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC1553CSW#PBF | 功能描述:IC SW REG CNTRLR 5BIT PROG20SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。