- 您現在的位置：買賣IC網 > PDF目錄377766 > LTC1955EUH (LINEAR TECHNOLOGY CORP) Dual Smart Card Interface with Serial Control PDF資料下載
參數資料
| 型號： | LTC1955EUH |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Smart Card Interface with Serial Control |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| 封裝： | 5 X 5 MM, 0.75 MM HEIGHT, MO-220WHHD, QFN-32 |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 259K |
| 代理商： | LTC1955EUH |
LTC1955
13
sn1955 1955fs
Electrical Fault Detection
Several types of faults are detected by the LTC1955. They
include V
CCA
/V
CCB
undervoltage, V
CCA
/V
CCB
overcurrent,
CLK A/CLK B, RST A/RST B, C8A, C4A short circuit, card
removal during a transaction, failed answer to reset (ATR),
supply undervoltage or UNDERV and chip overtemperature.
To prevent false errors from plaguing the microcontroller,
the electrical faults are acted upon only after a 5
μ
s (min)
timeout period. Card removal during transaction faults
initiate the deactivation sequence immediately.
V
CCA
/V
CCB
under voltage faults are determined by com-
paring the actual output voltage with the internal reference
voltage. If the output is more than ~5% below its set point
for the entire timeout period, the fault is reported and the
deactivation sequence is initiated.
V
CCA
/V
CCB
overcurrent faults are detected by comparing
the output current of the LDOs with an internal reference
level. If the current of an LDO is more than 100mA (typ) for
the entire timeout period, the fault is reported and the
deactivation sequence is initiated.
CLK A/CLK B and RST A/RST B faults are detected by
comparing the outputs of these pins with their expected
signals. If the signal on a pin is incorrect for the entire
timeout period, the fault is reported and the deactivation
sequence is initiated.
The clock channels are a special case. Since they can have
a free running clock, the error indication is accumulated
over a longer period of time without being cleared. Even
though the clock may be running, an error will still be
detected.
An overtemperature fault is detected by sensing the junc-
tion temperature of the IC. If the junction temperature
exceeds approximately 150
°
C for the entire timeout
period, the fault is reported by setting both fault bits (D4
and D12) and the deactivation sequence is initiated.
A card removal fault is determined as soon as the PRES A/
PRES B pin is high (for NC/NO = 0). Once this occurs the
fault is reported and the deactivation sequence is initiated.
If no card is present, and the application software attempts
to power up a card socket, an automatic fault will result on
that channel.
OPERATIOU
Short circuits on the I/O A/I/O B lines will not be detected
by the fault detection hardware; however, a short circuit
from these lines to their respective V
CCA
/V
CCB
pins will be
compliant with the maximum current limits set by appli-
cable standards (<15mA).
Answer to Reset (ATR) Fault Detection
Answer to Reset faults are detected by an internal counter
that is started once the RST A/B line goes high. If the DATA
pin remains high for 40,000 clock cycles, the ATR fault bit
for a given channel is set in the serial port’s status register
(see Table 1) and the FAULT pin is brought low.
An ATR fault can not occur if the clock mode of a channel
is set to synchronous. ATR faults will only occur for
asynchronous smart cards.
ATR faults are cleared by bringing the RST A/B pin low for
the faulted channel. This will also clear the FAULT pin to
the Hi-Z state (assuming no other errors are causing
FAULT to be low).
An ATR fault will not automatically deactivate a card
channel. It is the application programmer’s responsibility
to check the status register for ATR faults and deactivate
the smart card channel in accordance with smart card
standards. Generally the application has 50ms (EMV
2.1.3.1, 2.1.3.2) from the 40,000th clock pulse to deacti-
vate the card. Once the LTC1955 receives the deactivation
command, it will shut down a card channel in less than
250
μ
s.
Using the FAULT Pin
The FAULT pin can be used as an interrupt to a
microcontroller. It is an open-drain output and generally
requires a pull-up resistor. The FAULT pin will go low when
either an electrical fault or an answer to reset fault occurs
on either channel. Thus there are four possible faults that
can cause it to indicate a problem. The serial port’s status
register must be polled to find out what type of fault
occured and on which channel. The FAULT pin is logically
equivalent to D4+D5+D12+D13 (see Table 1).
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1957 | 40MHz to 900MHz Quadrature Demodulator |
| LT5500 | 40MHz to 900MHz Quadrature Demodulator |
| LT5511 | 40MHz to 900MHz Quadrature Demodulator |
| LT5515 | 40MHz to 900MHz Quadrature Demodulator |
| LT5517 | 40MHz to 900MHz Quadrature Demodulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1955EUH#PBF | 功能描述:IC INTERFACE DL SMART CARD 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955EUH#TR | 功能描述:IC SMART CARD INTERFC DUAL 32QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955EUH#TRPBF | 功能描述:IC INTERFACE DL SMART CARD 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955IUH#PBF | 功能描述:IC SMART CARD INTERFACE DL 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955IUH#TRPBF | 功能描述:IC SMART CARD INTERFACE DL 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
發布緊急采購，3分鐘左右您將得到回復。