- 您現在的位置：買賣IC網 > PDF目錄10109 > LTC2202CUK#TRPBF (Linear Technology)IC ADC 16-BIT 10MSPS 48-QFN PDF資料下載
參數資料
| 型號： | LTC2202CUK#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 13/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16-BIT 10MSPS 48-QFN |
| 標準包裝： | 2,000 |
| 位數： | 16 |
| 采樣率（每秒）： | 10M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 165mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-QFN-EP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分 |
| 配用： | DC919A-F-ND - BOARD DEMO 16BIT MSPS LTC2202 DC890B-ND - BOARD USB DATA COLLECTION |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC2203/LTC2202
20
22032fd
the new sample is small, the charging glitch seen at the
input will be small. If the input change is large, such as
the change seen with input frequencies near Nyquist, then
a larger charging glitch will be seen.
Common Mode Bias
The ADC sample-and-hold circuit requires differential
drive to achieve specied performance. Each input may
swing ±0.625V for the 2.5V range (PGA = 0) or ±0.417V
for the 1.667V range (PGA = 1), around a common mode
voltage of 1.25V. The VCM output pin (Pin 3) is designed
to provide the common mode bias level. VCM can be tied
directly to the center tap of a transformer to set the DC
input level or as a reference level to an op amp differential
driver circuit. The VCM pin must be bypassed to ground
close to the ADC with 2.2μF or greater.
Input Drive Impedence
As with all high performance, high speed ADCs the
dynamic performance of the LTC2203/LTC2202 can be
inuenced by the input drive circuitry, particularly the
second and third harmonics. Source impedance and
input reactance can inuence SFDR. At the rising edge of
CLK the sample and hold circuit will connect the 9.1pF
sampling capacitor to the input pin and start the sampling
period. The sampling period ends when CLK falls, hold-
ing the sampled input on the sampling capacitor. Ideally,
the input circuitry should be fast enough to fully charge
the sampling capacitor during the sampling period
1/(2FCLK); however, this is not always possible and the
incomplete settling may degrade the SFDR. The sampling
glitch has been designed to be as linear as possible to
minimize the effects of incomplete settling.
For the best performance it is recomended to have a source
impedence of 100Ω or less for each input. The source
impedence should be matched for the differential inputs.
Poor matching will result in higher even order harmonics,
especially the second.
INPUT DRIVE CIRCUITS
Figure 3 shows the LTC2203/LTC2202 being driven by an RF
transformer with a center-tapped secondary. The secondary
center tap is DC biased with VCM, setting the ADC input
signal at its optimum DC level. Figure 3 shows a 1:1 turns
ratio transformer. Other turns ratios can be used; however,
as the turns ratio increases so does the impedance seen by
the ADC. Source impedance greater than 50Ω can reduce
the input bandwidth and increase high frequency distor-
tion. A disadvantage of using a transformer is the loss of
low frequency response. Most small RF transformers have
poor performance at frequencies below 1MHz.
Figure 3. Single-Ended to Differential Conversion
Using a Transformer. Recommended for Input
Frequencies from 1MHz to 100MHz
LTC2203/
LTC2202
ANALOG
INPUT
T1 = COILCRAFT WBCI-IT OR
MA/COM ETC1-1T.
RESISTORS, CAPACITORS ARE
0402 PACKAGE SIZE, EXCEPT 2.2μF.
22032 F03
0.1μF
2.2μF
12pF
0.1μF
T1
1:1
25Ω
VCM
AIN+
AIN–
Figure 4. Using a Transmission Line Balun Transformer.
Recommended for Input Frequencies from 50MHz to 250MHz
0.1μF
AIN
+
AIN
–
4.7pF
2.2μF
4.7pF
VCM
ANALOG
INPUT
0.1μF
T1
1:1
T1 = MA/COM ETC1-1-13.
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE,
EXCEPT 2.2F.
22032 F04
25Ω
10Ω
25Ω
LTC2203/
LTC2202
Center-tapped transformers provide a convenient means
of DC biasing the secondary; however, they often show
poor balance at high input frequencies, resulting in large
2nd order harmonics.
Figure 4 shows transformer coupling using a transmis-
sion line balun transformer. This type of transformer has
much better high frequency response and balance than ux
coupled center tap transformers. Coupling capacitors are
added at the ground and input primary terminals to allow
the secondary terminals to be biased at 1.25V.
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72211L10PF8 | IC FIFO 512X9 SYNC 10NS 32-TQFP |
| VE-B3F-IV-F4 | CONVERTER MOD DC/DC 72V 150W |
| MS3100E14S-7P | CONN RCPT 3POS WALL MNT W/PINS |
| LTC1604ACG#TRPBF | IC A/D CONV 16BIT SAMPLNG 36SSOP |
| ADM207ARS | IC TXRX RS232 5DVR/3REC 24SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2202IUK | 制造商:Linear Technology 功能描述:ADC Single Pipelined 10Msps 16-bit Parallel 48-Pin QFN EP |
| LTC2202IUK#PBF | 功能描述:IC ADC 16-BIT 10MSPS 48-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2202IUK#TRPBF | 功能描述:IC ADC 16-BIT 10MSPS 48-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2202UK | 制造商:LINER 制造商全稱:Linear Technology 功能描述:16-Bit, 25Msps/10Msps ADCs |
| LTC2203 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:16-Bit, 25Msps/10Msps ADCs |
發布緊急采購，3分鐘左右您將得到回復。