參數資料
型號： LTC2228IUH#PBF
廠商： Linear Technology
文件頁數： 15/28頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 65MSPS SAMPL 32-QFN
標準包裝： 73
位數： 12
采樣率（每秒）： 65M
數據接口： 并聯
轉換器數目： 1
功率耗散（最大）： 240mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-WFQFN 裸露焊盤
供應商設備封裝： 32-QFN 裸露焊盤（5x5）
包裝： 管件
輸入數目和類型： 1 個單端，雙極; 1 個差分，雙極
產品目錄頁面： 1349 (CN2011-ZH PDF)
LTC2228/LTC2227/LTC2226
22
222876fb
APPLICATIONS INFORMATION
digital outputs of the LTC2228/LTC2227/LTC2226 should
drive a minimal capacitive load to avoid possible interaction
between the digital outputs and sensitive input circuitry.
The output should be buffered with a device such as an
ALVCH16373 CMOS latch. For full speed operation the
capacitive load should be kept under 10pF.
Lower OVDD voltages will also help reduce interference
from the digital outputs.
Data Format
Using the MODE pin, the LTC2228/LTC2227/LTC2226
parallel digital output can be selected for offset binary
or 2’s complement format. Connecting MODE to GND or
1/3VDD selects offset binary output format. Connecting
MODE to 2/3VDD or VDD selects 2’s complement output
format. An external resistor divider can be used to set the
1/3VDD or 2/3VDD logic values. Table 2 shows the logic
states for the MODE pin.
Table 2. MODE Pin Function
MODE PIN
OUTPUT FORMAT
CLOCK DUTY
CYCLE STABILIZER
0
Offset Binary
Off
1/3VDD
Offset Binary
On
2/3VDD
2’s Complement
On
VDD
2’s Complement
Off
Overow Bit
When OF outputs a logic high the converter is either over-
ranged or underranged.
Output Driver Power
Separate output power and ground pins allow the output
drivers to be isolated from the analog circuitry. The power
supply for the digital output buffers, OVDD, should be tied
to the same power supply as for the logic being driven.
For example if the converter is driving a DSP powered
by a 1.8V supply, then OVDD should be tied to that same
1.8V supply.
OVDD can be powered with any voltage from 500mV up to
3.6V. OGND can be powered with any voltage from GND
up to 1V and must be less than OVDD. The logic outputs
will swing between OGND and OVDD.
Output Enable
The outputs may be disabled with the output enable pin,
OE. OE high disables all data outputs including OF. The
data access and bus relinquish times are too slow to allow
the outputs to be enabled and disabled during full speed
operation. The output Hi-Z state is intended for use during
long periods of inactivity.
Sleep and Nap Modes
The converter may be placed in shutdown or nap modes
to conserve power. Connecting SHDN to GND results in
normal operation. Connecting SHDN to VDD and OE to VDD
results in sleep mode, which powers down all circuitry
including the reference and typically dissipates 1mW. When
exiting sleep mode it will take milliseconds for the output
data to become valid because the reference capacitors
have to recharge and stabilize. Connecting SHDN to VDD
and OE to GND results in nap mode, which typically dis-
sipates 15mW. In nap mode, the on-chip reference circuit
is kept on, so that recovery from nap mode is faster than
that from sleep mode, typically taking 100 clock cycles. In
both sleep and nap modes, all digital outputs are disabled
and enter the Hi-Z state.
Grounding and Bypassing
The LTC2228/LTC2227/LTC2226 require a printed circuit
board with a clean, unbroken ground plane. A multilayer
board with an internal ground plane is recommended.
Layout for the printed circuit board should ensure that
digital and analog signal lines are separated as much
as possible. In particular, care should be taken not to
run any digital track alongside an analog signal track or
underneath the ADC.
High quality ceramic bypass capacitors should be used at
the VDD, OVDD, VCM, REFH, and REFL pins. Bypass capaci-
tors must be located as close to the pins as possible. Of
particular importance is the 0.1μF capacitor between REFH
and REFL. This capacitor should be placed as close to the
device as possible (1.5mm or less). A size 0402 ceramic
capacitor is recommended. The large 2.2μF capacitor be-
tween REFH and REFL can be somewhat further away. The
traces connecting the pins and bypass capacitors must be
kept short and should be made as wide as possible.
相關PDF資料
PDF描述
VI-J13-MW-S CONVERTER MOD DC/DC 24V 100W
AD7980BRMZ ADC 16BIT 1MSPS 1.25LSB 10-MSOP
VE-B13-MW CONVERTER MOD DC/DC 24V 100W
AD7701ANZ IC ADC 16BIT LC2MOS 20-DIP
VI-B1L-MX-F2 CONVERTER MOD DC/DC 28V 75W
相關代理商/技術參數
參數描述
LTC2228IUH-TR 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65/40/25Msps Low Power 3V ADCs
LTC2228IUH-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65/40/25Msps Low Power 3V ADCs
LTC2229 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 80Msps Low Power 3V ADC
LTC2229CUH 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 80Msps Low Power 3V ADC
LTC2229CUH#PBF 功能描述:IC ADC 12-BIT 80MSPS 3V 32-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*