- 您現在的位置：買賣IC網 > PDF目錄10660 > LTC2228IUH#PBF (Linear Technology)IC ADC 12BIT 65MSPS SAMPL 32-QFN PDF資料下載
參數資料
| 型號： | LTC2228IUH#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 65MSPS SAMPL 32-QFN |
| 標準包裝： | 73 |
| 位數： | 12 |
| 采樣率（每秒）： | 65M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 240mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，雙極; 1 個差分，雙極 |
| 產品目錄頁面： | 1349 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2228/LTC2227/LTC2226
17
222876fb
APPLICATIONS INFORMATION
Single-Ended Input
For cost-sensitive applications, the analog inputs can be
driven single ended. With a single-ended input the har-
monic distortion and INL will degrade, but the SNR and
DNL will remain unchanged. For a single-ended input, AIN+
should be driven with the input signal and AIN– should be
connected to 1.5V or VCM.
Common Mode Bias
For optimal performance the analog inputs should be driven
differentially. Each input should swing ±0.5V for the 2V
range or ±0.25V for the 1V range, around a common mode
voltage of 1.5V. The VCM output pin (Pin 31) may be used
to provide the common mode bias level. VCM can be tied
directly to the center tap of a transformer to set the DC
input level or as a reference level to an op amp differential
driver circuit. The VCM pin must be bypassed to ground
close to the ADC with a 2.2μF or greater capacitor.
Input Drive Impedance
As with all high performance, high speed ADCs, the dy-
namic performance of the LTC2228/LTC2227/LTC2226 can
be inuenced by the input drive circuitry, particularly the
second and third harmonics. Source impedance and input
reactance can inuence SFDR. At the falling edge of CLK,
the sample-and-hold circuit will connect the 4pF sampling
capacitor to the input pin and start the sampling period.
The sampling period ends when CLK rises, holding the
sampled input on the sampling capacitor. Ideally the input
circuitry should be fast enough to fully charge the sam-
pling capacitor during the sampling period 1/(2FENCODE);
however, this is not always possible and the incomplete
settling may degrade the SFDR. The sampling glitch has
been designed to be as linear as possible to minimize the
effects of incomplete settling.
For the best performance, it is recommended to have a
source impedance of 100Ω or less for each input. The
source impedance should be matched for the differential
inputs. Poor matching will result in higher even order
harmonics, especially the second.
Input Drive Circuits
Figure 3 shows the LTC2228/LTC2227/LTC2226 being
driven by an RF transformer with a center tapped sec-
ondary. The secondary center tap is DC biased with VCM,
setting the ADC input signal at its optimum DC level.
Terminating on the transformer secondary is desirable,
as this provides a common mode path for charging
glitches caused by the sample and hold. Figure 3 shows
a 1:1 turns ratio transformer. Other turns ratios can be
used if the source impedance seen by the ADC does not
exceed 100Ω for each ADC input. A disadvantage of us-
ing a transformer is the loss of low frequency response.
Most small RF transformers have poor performance at
frequencies below 1MHz.
Figure 4 demonstrates the use of a differential amplier to
convert a single-ended input signal into a differential input
signal. The advantage of this method is that it provides
low frequency input response; however, the limited gain
bandwidth of most op amps will limit the SFDR at high
input frequencies.
25Ω
0.1μF
AIN
+
AIN
–
12pF
2.2μF
VCM
LTC2228/27/26
ANALOG
INPUT
0.1μF
T1
1:1
T1 = MA/COM ETC1-1T
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
222876 F03
Figure 3. Single-Ended to Differential Conversion Using a Transformer
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J13-MW-S | CONVERTER MOD DC/DC 24V 100W |
| AD7980BRMZ | ADC 16BIT 1MSPS 1.25LSB 10-MSOP |
| VE-B13-MW | CONVERTER MOD DC/DC 24V 100W |
| AD7701ANZ | IC ADC 16BIT LC2MOS 20-DIP |
| VI-B1L-MX-F2 | CONVERTER MOD DC/DC 28V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2228IUH-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65/40/25Msps Low Power 3V ADCs |
| LTC2228IUH-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65/40/25Msps Low Power 3V ADCs |
| LTC2229 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 80Msps Low Power 3V ADC |
| LTC2229CUH | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 80Msps Low Power 3V ADC |
| LTC2229CUH#PBF | 功能描述:IC ADC 12-BIT 80MSPS 3V 32-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。