- 您現在的位置：買賣IC網 > PDF目錄10071 > LTC2230IUP#TRPBF (Linear Technology)IC ADC 10BIT 170MSPS 64-QFN PDF資料下載
參數資料
| 型號： | LTC2230IUP#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 17/32頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 170MSPS 64-QFN |
| 標準包裝： | 2,000 |
| 位數： | 10 |
| 采樣率（每秒）： | 170M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 1.18W |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 64-QFN（9x9） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，雙極; 1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC2230/LTC2231
24
22301fb
as 50
Ω to external circuitry and may eliminate the need for
external damping resistors.
As with all high speed/high resolution converters, the
digital output loading can affect the performance. The
digital outputs of the LTC2230/LTC2231 should drive a
minimal capacitive load to avoid possible interaction be-
tween the digital outputs and sensitive input circuitry. The
output should be buffered with a device such as an
ALVCH16373 CMOS latch. For full speed operation the
capacitive load should be kept under 10pF.
Lower OVDD voltages will also help reduce interference
from the digital outputs.
Digital Output Buffers (LVDS Mode)
Figure 13b shows an equivalent circuit for a differential
output pair in the LVDS output mode. A 3.5mA current is
steered from OUT+ to OUT– or vice versa which creates a
±350mV differential voltage across the 100Ω termination
resistor at the LVDS receiver. A feedback loop regulates
the common mode output voltage to 1.25V. For proper
operation each LVDS output pair needs an external 100
Ω
termination resistor, even if the signal is not used (such as
OF+/OF– or CLKOUT+/CLKOUT–). To minimize noise the
PC board traces for each LVDS output pair should be
routed close together. To minimize clock skew all LVDS PC
board traces should have about the same length.
APPLICATIO S I FOR ATIO
WU
UU
Data Format
The LTC2230/LTC2231 parallel digital output can be se-
lected for offset binary or 2’s complement format. The
format is selected with the MODE pin. Connecting MODE
to GND or 1/3VDD selects offset binary output format.
Connecting MODE to 2/3VDD or VDD selects 2’s comple-
ment output format. An external resistor divider can be
used to set the 1/3VDD or 2/3VDD logic values. Table 3
shows the logic states for the MODE pin.
LTC2230/LTC2231
22301 F13b
OVDD
LVDS
RECEIVER
OGND
1.25V
D
OUT+
OUT–
100
Ω
+
–
3.5mA
10k
Figure 13b. Digital Output in LVDS Mode
Table 3. MODE Pin Function
Clock Duty
MODE Pin
Output Format
Cycle Stablizer
0
Offset Binary
Off
1/3VDD
Offset Binary
On
2/3VDD
2’s Complement
On
VDD
2’s Complement
Off
Overflow Bit
An overflow output bit indicates when the converter is
overranged or underranged. In CMOS mode, a logic high
on the OFA pin indicates an overflow or underflow on the
A data bus, while a logic high on the OFB pin indicates an
overflow or underflow on the B data bus. In LVDS mode,
a differential logic high on the OF+/OF– pins indicates an
overflow or underflow.
Output Clock
The ADC has a delayed version of the ENC+ input available
as a digital output, CLKOUT. The CLKOUT pin can be used
to synchronize the converter data to the digital system. This
is necessary when using a sinusoidal encode. In all CMOS
modes, A bus data will be updated just after CLKOUTA rises
and can be latched on the falling edge of CLKOUTA. In demux
CMOS mode with interleaved update, B bus data will be
updated just after CLKOUTB rises and can be latched on the
falling edge of CLKOUTB. In demux CMOS mode with si-
multaneous update, B bus data will be updated just after
CLKOUTB falls and can be latched on the rising edge of
CLKOUTB. In LVDS mode, data will be updated just after
CLKOUT+/CLKOUT– rises and can be latched on the falling
edge of CLKOUT+/CLKOUT–.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3101R20-21P | CONN RCPT 9POS PANEL MNT W/PINS |
| MS3102A20-29SZ | CONN RCPT 17POS BOX MNT W/SCKT |
| IDT72V801L20PF8 | IC SYNC FIFO 256X9 20NS 64QFP |
| IDT7206L50J | IC FIFO 8192X18 50NS 32PLCC |
| IDT7206L50P | IC FIFO 8192X18 50NS 28DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2230UP | 制造商:LINER 制造商全稱:Linear Technology 功能描述:10-Bit,170Msps/135Msps ADCs |
| LTC2231 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:10-Bit,170Msps/135Msps ADCs |
| LTC2231CUP | 制造商:LINER 制造商全稱:Linear Technology 功能描述:10-Bit,170Msps/135Msps ADCs |
| LTC2231CUP#PBF | 功能描述:IC ADC 10BIT 135MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2231CUP#TRPBF | 功能描述:IC ADC 10BIT 135MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。