AIN+ (Pins 1, 2): Positive Differential Analog Inp" />
參數資料
型號： LTC2242CUP-10#TRPBF
廠商： Linear Technology
文件頁數： 2/30頁
文件大小： 0K
描述： IC ADC 10BIT 250MSPS 64-QFN
標準包裝： 2,000
位數： 10
采樣率（每秒）： 250M
數據接口： 并聯
轉換器數目： 1
功率耗散（最大）： 975mW
電壓電源： 單電源
工作溫度： 0°C ~ 75°C
安裝類型： 表面貼裝
封裝/外殼： 64-WFQFN 裸露焊盤
供應商設備封裝： 64-QFN（9x9）
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分，雙極
LTC2242-10
10
224210fd
pin FuncTions
AIN+ (Pins 1, 2): Positive Differential Analog Input.
AIN– (Pins 3, 4): Negative Differential Analog Input.
REFHA (Pins 5, 6): ADC High Reference. Bypass to
Pins 7, 8 with 0.1F ceramic chip capacitor, to Pins 11,
12 with a 2.2F ceramic capacitor and to ground with 1F
ceramic capacitor.
REFLB (Pins 7, 8): ADC Low Reference. Bypass to Pins
5, 6 with 0.1F ceramic chip capacitor. Do not connect to
Pins 11, 12.
REFHB (Pins 9, 10): ADC High Reference. Bypass to
Pins 11, 12 with 0.1F ceramic chip capacitor. Do not
connect to Pins 5, 6.
REFLA (Pins 11, 12): ADC Low Reference. Bypass to
Pins 9, 10 with 0.1F ceramic chip capacitor, to Pins 5,
6 with a 2.2F ceramic capacitor and to ground with 1F
ceramic capacitor.
VDD (Pins 13, 14, 15, 62, 63): 2.5V Supply. Bypass to
GND with 0.1F ceramic chip capacitors.
GND (Pins 16, 61, 64): ADC Power Ground.
ENC+ (Pin 17): Encode Input. Conversion starts on the
positive edge.
ENC– (Pin 18): Encode Complement Input. Conversion
starts on the negative edge. Bypass to ground with 0.1F
ceramic for single-ended encode signal.
SHDN(Pin19):ShutdownModeSelectionPin.Connecting
SHDN to GND and OE to GND results in normal operation
with the outputs enabled. Connecting SHDN to GND and
OE to VDD results in normal operation with the outputs at
high impedance. Connecting SHDN to VDD and OE to GND
results in nap mode with the outputs at high impedance.
Connecting SHDN to VDD and OE to VDD results in sleep
mode with the outputs at high impedance.
OE (Pin 20): Output Enable Pin. Refer to SHDN pin function.
DNC (Pins 21, 22, 23, 24): Do not connect these pins.
D0–/D0+ to D9–/D9+ (Pins 27, 28, 29, 30, 31, 32, 37,
38, 39, 40, 43, 44, 45, 46, 47, 48, 51, 52, 53, 54):
LVDS Digital Outputs. All LVDS outputs require differential
100Ω termination resistors at the LVDS receiver. D9–/D9+
is the MSB.
OGND (Pins 25, 33, 41, 50): Output Driver Ground.
OVDD (Pins 26, 34, 42, 49): Positive Supply for the Out-
put Drivers. Bypass to ground with 0.1F ceramic chip
capacitor.
CLKOUT–/CLKOUT+ (Pins 35 to 36): LVDS Data Valid
Output. Latch data on rising edge of CLKOUT–, falling
edge of CLKOUT+.
OF–/OF+ (Pins 55 to 56): LVDS Over/Under Flow Output.
High when an over or under flow has occurred.
LVDS (Pin 57): Output Mode Selection Pin. Connecting
LVDS to 0V selects full rate CMOS mode. Connecting LVDS
to 1/3VDD selects demux CMOS mode with simultaneous
update. Connecting LVDS to 2/3VDD selects demux CMOS
mode with interleaved update. Connecting LVDS to VDD
selects LVDS mode.
MODE (Pin 58): Output Format and Clock Duty Cycle
Stabilizer Selection Pin. Connecting MODE to 0V selects
offset binary output format and turns the clock duty cycle
stabilizer off. Connecting MODE to 1/3VDD selects offset
binaryoutputformatandturnstheclockdutycyclestabilizer
on. Connecting MODE to 2/3VDD selects 2’s complement
output format and turns the clock duty cycle stabilizer on.
Connecting MODE to VDD selects 2’s complement output
format and turns the clock duty cycle stabilizer off.
SENSE(Pin59):ReferenceProgrammingPin.Connecting
SENSE to VCM selects the internal reference and a ±0.5V
input range. Connecting SENSE to VDD selects the internal
reference and a ±1V input range. An external reference
greater than 0.5V and less than 1V applied to SENSE
selects an input range of ±VSENSE. ±1V is the largest valid
input range.
VCM (Pin 60): 1.25V Output and Input Common Mode
Bias. Bypass to ground with 2.2F ceramic chip capacitor.
GND (Exposed Pad) (Pin 65): ADC Power Ground. The
exposed pad on the bottom of the package needs to be
soldered to ground.
(LVDS Mode)
相關PDF資料
PDF描述
LT1130ACSW#TR IC TXRX 5V RS232 LP CAPS 28SOIC
AD7711AQ IC ADC 24BIT RTD I SOURCE 24CDIP
LTC486CSW IC DVR RS485 LOW PWR QUAD 16SOIC
IDT72231L25JI IC FIFO SYNC 512X9 25NS 32PLCC
LTC2221CUP#PBF IC ADC 12-BIT 135MSPS 64-QFN
相關代理商/技術參數
參數描述
LTC2242CUP-12 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 250Msps ADC
LTC2242CUP-12#PBF 制造商:Linear Technology 功能描述:Single ADC Pipelined 250Msps 12-bit Parallel/LVDS 64-Pin QFN EP 制造商:Linear Technology 功能描述:IC ADC 12BIT 250MSPS 64-QFN 制造商:Linear Technology 功能描述:ADC 12BIT 250MSPS 64QFN 制造商:Linear Technology 功能描述:ADC, 12BIT, 250MSPS, 64QFN 制造商:Linear Technology 功能描述:MS-ADC/High Speed, 12-bit, 250Msps ADC 制造商:Linear Technology 功能描述:IC, ADC, 12BIT, 250MSPS, QFN-64, Resolution (Bits):12bit, Sampling Rate:250MSPS, Supply Voltage Type:Single, Supply Voltage Min:2.375V, Supply Voltage Max:2.625V, Supply Current:285mA, Digital IC Case Style:QFN, No. of Pins:64 , RoHS Compliant: Yes
LTC2242CUP-12#TRPBF 制造商:Linear Technology 功能描述:IC ADC 12BIT 250MSPS 64-QFN
LTC2242IUP-10#PBF 功能描述:IC ADC 10BIT 250MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
LTC2242IUP-10#TRPBF 功能描述:IC ADC 10BIT 250MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*