- 您現在的位置：買賣IC網 > PDF目錄10064 > LTC2242CUP-10#TRPBF (Linear Technology)IC ADC 10BIT 250MSPS 64-QFN PDF資料下載
參數資料
| 型號： | LTC2242CUP-10#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 6/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 250MSPS 64-QFN |
| 標準包裝： | 2,000 |
| 位數： | 10 |
| 采樣率（每秒）： | 250M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 975mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 75°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 64-QFN（9x9） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
LTC2242-10
14
224210fd
applicaTions inForMaTion
DYNAMIC PERFORMANCE
Signal-to-Noise Plus Distortion Ratio
The signal-to-noise plus distortion ratio [S/(N + D)] is
the ratio between the RMS amplitude of the fundamen-
tal input frequency and the RMS amplitude of all other
frequency components at the ADC output. The output is
band limited to frequencies above DC to below half the
sampling frequency.
Signal-to-Noise Ratio
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC.
Total Harmonic Distortion
Total harmonic distortion is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental
itself. The out-of-band harmonics alias into the frequency
band between DC and half the sampling frequency. THD
is expressed as:
THD
= 20Log
V22
+ V32 + V42 +...Vn2
(
)/V1
where V1 is the RMS amplitude of the fundamental fre-
quencyandV2throughVnaretheamplitudesofthesecond
through nth harmonics. The THD calculated in this data
sheet uses all the harmonics up to the fifth.
Intermodulation Distortion
If the ADC input signal consists of more than one spectral
component, the ADC transfer function nonlinearity can
produce intermodulation distortion (IMD) in addition to
THD. IMD is the change in one sinusoidal input caused
by the presence of another sinusoidal input at a different
frequency.
If two pure sine waves of frequencies fa and fb are ap-
plied to the ADC input, nonlinearities in the ADC transfer
function can create distortion products at the sum and
difference frequencies of mfa ± nfb, where m and n = 0,
1, 2, 3, etc. The 3rd order intermodulation products are
2fa + fb, 2fb + fa, 2fa – fb and 2fb – fa. The intermodula-
tion distortion is defined as the ratio of the RMS value of
either input tone to the RMS value of the largest 3rd order
intermodulation product.
Spurious Free Dynamic Range (SFDR)
Spuriousfreedynamicrangeisthepeakharmonicorspuri-
ous noise that is the largest spectral component excluding
the input signal and DC. This value is expressed in decibels
relative to the RMS value of a full scale input signal.
Full Power Bandwidth
The full power bandwidth is that input frequency at which
theamplitudeofthereconstructedfundamentalisreduced
by 3dB for a full scale input signal.
Aperture Delay Time
The time from when a rising ENC+ equals the ENC– voltage
to the instant that the input signal is held by the sample
and hold circuit.
Aperture Delay Jitter
The variation in the aperture delay time from conversion
to conversion. This random variation will result in noise
when sampling an AC input. The signal to noise ratio due
to the jitter alone will be:
SNRJITTER = –20log (2π fIN tJITTER)
CONVERTER OPERATION
As shown in Figure 1, the LTC2242-10 is a CMOS pipelined
multi-step converter. The converter has five pipelined ADC
stages; a sampled analog input will result in a digitized
valuefivecycleslater(seetheTimingDiagramsection).For
optimal performance the analog inputs should be driven
differentially. The encode input is differential for improved
common mode noise immunity. The LTC2242-10 has two
phases of operation, determined by the state of the dif-
ferential ENC+/ENC– input pins. For brevity, the text will
refer to ENC+ greater than ENC– as ENC high and ENC+
less than ENC– as ENC low.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1130ACSW#TR | IC TXRX 5V RS232 LP CAPS 28SOIC |
| AD7711AQ | IC ADC 24BIT RTD I SOURCE 24CDIP |
| LTC486CSW | IC DVR RS485 LOW PWR QUAD 16SOIC |
| IDT72231L25JI | IC FIFO SYNC 512X9 25NS 32PLCC |
| LTC2221CUP#PBF | IC ADC 12-BIT 135MSPS 64-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2242CUP-12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 250Msps ADC |
| LTC2242CUP-12#PBF | 制造商:Linear Technology 功能描述:Single ADC Pipelined 250Msps 12-bit Parallel/LVDS 64-Pin QFN EP 制造商:Linear Technology 功能描述:IC ADC 12BIT 250MSPS 64-QFN 制造商:Linear Technology 功能描述:ADC 12BIT 250MSPS 64QFN 制造商:Linear Technology 功能描述:ADC, 12BIT, 250MSPS, 64QFN 制造商:Linear Technology 功能描述:MS-ADC/High Speed, 12-bit, 250Msps ADC 制造商:Linear Technology 功能描述:IC, ADC, 12BIT, 250MSPS, QFN-64, Resolution (Bits):12bit, Sampling Rate:250MSPS, Supply Voltage Type:Single, Supply Voltage Min:2.375V, Supply Voltage Max:2.625V, Supply Current:285mA, Digital IC Case Style:QFN, No. of Pins:64 , RoHS Compliant: Yes |
| LTC2242CUP-12#TRPBF | 制造商:Linear Technology 功能描述:IC ADC 12BIT 250MSPS 64-QFN |
| LTC2242IUP-10#PBF | 功能描述:IC ADC 10BIT 250MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2242IUP-10#TRPBF | 功能描述:IC ADC 10BIT 250MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。