- 您現在的位置：買賣IC網 > PDF目錄383291 > LTC2400IS8 (LINEAR TECHNOLOGY CORP) 24-Bit uPower No Latency ADC in SO-8 PDF資料下載
參數資料
| 型號： | LTC2400IS8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 24-Bit uPower No Latency ADC in SO-8 |
| 中文描述： | 1-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SO-8 |
| 文件頁數： | 22/40頁 |
| 文件大?。?/td> | 455K |
| 代理商： | LTC2400IS8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
22
LTC2400
connection resistance. The LTC2400’s power supply cur-
rent flowing through the 0.01
resistance of the common
ground pin will develop a 2.5
μ
V offset signal. For a
reference voltage V
REF
= 2.5V, this represents a 1ppm
offset error.
In an alternative configuration, the GND pin of the converter
can be the single-point-ground in a single point grounding
system. The input signal ground, the reference signal
ground, the digital drivers ground (usually the digital
ground) and the power supply ground (the analog ground)
should be connected in a star configuration with the com-
mon point located as close to the GND pin as possible.
The power supply current during the conversion state
should be kept to a minimum. This is achieved by restrict-
ing the number of digital signal transitions occurring
during this period.
While a digital input signal is in the range 0.5V to
(V
CC
–0.5V), the CMOS input receiver draws additional
current from the power supply. It should be noted that,
when any one of the digital input signals (F
O
, CS and SCK
in External SCK mode of operation) is within this range, the
LTC2400 power supply current may increase even if the
signal in question is at a valid logic level. For micropower
operation and in order to minimize the potential errors due
to additional ground pin current, it is recommended to
drive all digital input signals to full CMOS levels
[V
IL
< 0.4V and V
OH
> (V
CC
– 0.4V)].
Severe ground pin current disturbances can also occur
due to the undershoot of fast digital input signals. Under-
shoot and overshoot can occur because of the impedance
mismatch at the converter pin when the transition time of
an external control signal is less than twice the propaga-
tion delay from the driver to LTC2400. For reference, on
a regular FR-4 board, signal propagation velocity is ap-
proximately 183ps/inch for internal traces and 170ps/inch
for surface traces. Thus, a driver generating a control
signal with a minimum transition time of 1ns must be
connected to the converter pin through a trace shorter
than 2.5 inches. This problem becomes particularly diffi-
cult when shared control lines are used and multiple
reflections may occur. The solution is to carefully termi-
nate all transmission lines close to their characteristic
impedance.
APPLICATIO
S I
N
FOR
ATIO
U
W
U
V
REF
V
IN
V
CC
R
SW
5k
AVERAGE INPUT CURRENT:
I
IN
= 0.25(V
IN
– 0.5 V
REF
)fC
EQ
I
REF(LEAK)
I
REF(LEAK)
V
CC
R
SW
5k
C
10pF (TYP)
R
SW
5k
I
IN(LEAK)
I
IN
2400 F15
I
IN(LEAK)
SWITCHING FREQUENCY
f = 153.6kHz FOR INTERNAL OSCILLATOR (f
O
= LOGIC LOW OR HIGH)
f = f
EOSC
FOR EXTERNAL OSCILLATORS
GND
Figure 15. LTC2400 Equivalent Analog Input Circuit
Parallel termination near the LTC2400 pin will eliminate
this problem but will increase the driver power dissipation.
A series resistor between 27
and 56
placed near the
driver or near the LTC2400 pin will also eliminate this
problem without additional power dissipation. The actual
resistor value depends upon the trace impedance and
connection topology.
Driving the Input and Reference
The analog input and reference of the typical delta-sigma
analog-to-digital converter are applied to a switched ca-
pacitor network. This network consists of capacitors
switching between the analog input (V
IN
), ground (Pin 4)
and the reference (V
REF
). The result is small current spikes
seen at both V
IN
and V
REF
. A simplified input equivalent
circuit is shown in Figure 15.
The key to understanding the effects of this dynamic input
current is based on a simple first order RC time constant
model. Using the internal oscillator, the LTC2400’s inter-
nal switched capacitor network is clocked at 153,600Hz
corresponding to a 6.5
μ
s sampling period. Fourteen time
constants are required each time a capacitor is switched in
order to achieve 1ppm settling accuracy.
Therefore, the equivalent time constant at V
IN
and V
REF
should be less than 6.5
μ
s/14 = 460ns in order to achieve
1ppm accuracy.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2400 | 24-Bit uPower No Latency ADC in SO-8 |
| LTC2400C | 24-Bit uPower No Latency ADC in SO-8 |
| LTC2400CS8 | 24-Bit uPower No Latency ADC in SO-8 |
| LTC2400I | 24-Bit uPower No Latency ADC in SO-8 |
| LTC3456 | 2-Cell, Multi-Output DC/DC Converter with USB Power Manager |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2400IS8#PBF | 功能描述:IC A/D CONV 24BIT MICRPWR 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2400IS8#PBF | 制造商:Linear Technology 功能描述:IC ADC 24BIT SOIC-8 制造商:Linear Technology 功能描述:IC, ADC, 24BIT, SOIC-8 |
| LTC2400IS8#TR | 功能描述:IC ADC 24BIT MICROPOWER 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2400IS8#TRPBF | 功能描述:IC A/D CONV 24BIT MICRPWR 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2401CMS | 功能描述:IC ADC 24BIT 1CH MICROPWR 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。