- 您現在的位置：買賣IC網 > PDF目錄377769 > LTC2410IGN (LINEAR TECHNOLOGY CORP) 24-Bit No Latency ADC with Differential Input and Differential Reference PDF資料下載
參數資料
| 型號： | LTC2410IGN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 24-Bit No Latency ADC with Differential Input and Differential Reference |
| 中文描述： | 1-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件頁數： | 9/44頁 |
| 文件大小： | 778K |
| 代理商： | LTC2410IGN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
LTC2410
9
Input Voltage Range
The analog input is truly differential with an absolute/
common mode range for the IN
+
and IN
–
input pins
extending from GND – 0.3V to V
CC
+ 0.3V. Outside
these limits the ESD protection devices begin to turn on
and the errors due to input leakage current increase
rapidly. Within these limits the LTC2410 converts the
bipolar differential input signal, V
IN
= IN
+
– IN
–
, from
–FS = –0.5 V
REF
to +FS = 0.5 V
REF
where V
REF
=
REF
+
– REF
–
. Outside this range the converter indicates the
overrange or the underrange condition using distinct
output codes.
Input signals applied to IN
+
and IN
–
pins may extend by
300mV below ground and above V
CC
. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN
+
and IN
–
pins without affecting the perfor-
mance of the device. In the physical layout, it is important
to maintain the parasitic capacitance of the connection
between these series resistors and the corresponding pins
as low as possible; therefore, the resistors should be
located as close as practical to the pins. The effect of the
series resistance on the converter accuracy can be evalu-
ated from the curves presented in the Input Current/
Reference Current sections. In addition, series resistors
will introduce a temperature dependent offset error due to
the input leakage current. A 1nA input leakage current will
develop a 1ppm offset error on a 5k resistor if V
REF
= 5V.
This error has a very strong temperature dependency.
Output Data Format
The LTC2410 serial output data stream is 32 bits long. The
first 3 bits represent status information indicating the sign
and conversion state. The next 24 bits are the conversion
result, MSB first. The remaining 5 bits are sub LSBs
beyond the 24-bit level that may be included in averaging
or discarded without loss of resolution. The third and
fourth bit together are also used to indicate an underrange
condition (the differential input voltage is below –FS) or an
overrange condition (the differential input voltage is above
+FS).
Bit 31 (first output bit) is the end of conversion (EOC)
indicator. This bit is available at the SDO pin during the
conversion and sleep states whenever the CS pin is LOW.
This bit is HIGH during the conversion and goes LOW
when the conversion is complete.
Bit 30 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit 29 (third output bit) is the conversion result sign indi-
cator (SIG). If V
IN
is >0, this bit is HIGH. If V
IN
is <0, this
bit is LOW.
Bit 28 (fourth output bit) is the most significant bit (MSB)
of the result. This bit in conjunction with Bit 29 also
provides the underrange or overrange indication. If both
Bit 29 and Bit 28 are HIGH, the differential input voltage is
above +FS. If both Bit 29 and Bit 28 are LOW, the
differential input voltage is below –FS.
The function of these bits is summarized in Table 1.
Table 1. LTC2410 Status Bits
Bit 31
EOC
0
0
0
0
Bit 30 Bit 29 Bit 28
DMY
SIG
0
1
0
1
0
0
0
0
Input Range
V
IN
≥
0.5 V
REF
0V
≤
V
IN
< 0.5 V
REF
–0.5 V
REF
≤
V
IN
< 0V
V
IN
< –0.5 V
REF
MSB
1
0
1
0
Bits 28-5 are the 24-bit conversion result MSB first.
Bit 5 is the least significant bit (LSB).
Bits 4-0 are sub LSBs below the 24-bit level. Bits 4-0 may
be included in averaging or discarded without loss of
resolution.
Data is shifted out of the SDO pin under control of the serial
clock (SCK), see Figure 3. Whenever CS is HIGH, SDO
remains high impedance and any externally generated
SCK clock pulses are ignored by the internal data out shift
register.
In order to shift the conversion result out of the device, CS
must first be driven LOW. EOC is seen at the SDO pin of the
device once CS is pulled LOW. EOC changes real time from
HIGH to LOW at the completion of a conversion. This
signal may be used as an interrupt for an external
microcontroller. Bit 31 (EOC) can be captured on the first
rising edge of SCK. Bit 30 is shifted out of the device on the
first falling edge of SCK. The final data bit (Bit 0) is shifted
out on the falling edge of the 31st SCK and may be latched
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2410 | 20-Bit Universal Bus Driver With 3-State Outputs 56-SSOP -40 to 85 |
| LTC2410C | 20-Bit Universal Bus Driver With 3-State Outputs 56-TVSOP -40 to 85 |
| LTC2410I | 20-Bit Universal Bus Driver With 3-State Outputs 56-SSOP -40 to 85 |
| LTC2411 | 2.7V to 5.5V Micropower 24-Bit Differential Σ△ Analog to Digital Converter(2.7V ～5.5V，微功耗，24位差分Σ△串行模數轉換器) |
| LTC2413CGN | 24-Bit No Latency ADC, with Simultaneous 50Hz/60Hz Rejection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2410IGN#PBF | 功能描述:IC ADC 24BIT DIFF INP/REF 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2410IGN#TR | 功能描述:IC ADC 24BIT DIFF INP/REF 16SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2410IGN#TRPBF | 功能描述:IC ADC 24BIT DIFF INP/REF 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2410IGNPBF | 制造商:Linear Technology 功能描述:ADC 7.5sps 24-Bit Serial SSOP16 |
| LTC2411-1CMS | 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。