- 您現在的位置：買賣IC網 > PDF目錄377769 > LTC2411-1 (Linear Technology Corporation) 16-Bit Universal Bus Driver With 3-State Outputs 48-TVSOP -40 to 85 PDF資料下載
參數資料
| 型號： | LTC2411-1 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 16-Bit Universal Bus Driver With 3-State Outputs 48-TVSOP -40 to 85 |
| 中文描述： | 2路差分輸入24位ADC的無延遲局副局長 |
| 文件頁數： | 19/36頁 |
| 文件大?。?/td> | 409K |
| 代理商： | LTC2411-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC2412
19
2412f
APPLICATIU
W
U
U
Figure 7. External Serial Clock, CS = 0 Operation (2-Wire)
EOC
BIT 31
SDO
SCK
(EXTERNAL)
CS
MSB
SIG
CH0/CH1
BIT 0
LSB
24
BIT 5
BIT 27
BIT 26
BIT 28
BIT 29
BIT 30
DATA OUTPUT
CONVERSION
2412 F07
CONVERSION
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
V
CC
V
CC
F
O
REF
+
SCK
CH1
+
CH1
–
SDO
GND
CS
1
14
2
3
13
6
7
12
8, 9, 10, 15, 16
11
REFERENCE
VOLTAGE
0.1V TO V
CC
CH0
+
CH0
–
4
5
ANALOG INPUT RANGE
–0.5V
REF
TO 0.5V
REF
1
μ
F
2.7V TO 5.5V
LTC2412
2-WIRE
INTERFACE
REF
–
typically 1ms after V
CC
exceeds 2V. The level applied to
SCK at this time determines if SCK is internal or external.
SCK must be driven LOW prior to the end of POR in order
to enter the external serial clock timing mode.
Since CS is tied LOW, the end-of-conversion (EOC) can be
continuously monitored at the SDO pin during the convert
and sleep states. EOC may be used as an interrupt to an
external controller indicating the conversion result is
ready. EOC = 1 while the conversion is in progress and
EOC=0 once the conversion ends. On the falling edge of
EOC, the conversion result is loaded into an internal static
shift register. Data is shifted out the SDO pin on each
falling edge of SCK enabling external circuitry to latch data
on the rising edge of SCK. EOC can be latched on the first
rising edge of SCK. On the 32nd falling edge of SCK, SDO
goes HIGH (EOC=1) indicating a new conversion has
begun.
Internal Serial Clock, Single Cycle Operation
This timing mode uses an internal serial clock to shift out
the conversion result and a CS signal to monitor and
control the state of the conversion cycle, see Figure 8.
In order to select the internal serial clock timing mode, the
serial clock pin (SCK) must be floating (Hi-Z) or pulled
HIGH prior to the falling edge of CS. The device will not
enter the internal serial clock mode if SCK is driven LOW
on the falling edge of CS. An internal weak pull-up resistor
is active on the SCK pin during the falling edge of CS;
therefore, the internal serial clock timing mode is auto-
matically selected if SCK is not externally driven.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
Once CS is pulled LOW, SCK goes LOW and EOC is output
to the SDO pin. EOC = 1 while a conversion is in progress
and EOC = 0 if the device is in the sleep state.
When testing EOC, if the conversion is complete (EOC = 0),
the device will exit the sleep state during the EOC test. In
order to allow the device to return to the low power sleep
state, CS must be pulled HIGH before the first rising edge
of SCK. In the internal SCK timing mode, SCK goes HIGH
and the device begins outputting data at time t
EOCtest
after
the falling edge of CS (if EOC = 0) or t
EOCtest
after EOC goes
LOW (if CS is LOW during the falling edge of EOC). The
value of t
EOCtest
is 23
μ
s if the device is using its internal
oscillator (F
0
= logic LOW or HIGH). If F
O
is driven by an
external oscillator of frequency f
EOSC
, then t
EOCtest
is
3.6/f
EOSC
. If CS is pulled HIGH before time t
EOCtest
, the
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2412 | 16-Bit Universal Bus Driver With 3-State Outputs 48-SSOP -40 to 85 |
| LTC2412CGN | 16-Bit Universal Bus Driver With 3-State Outputs 48-TVSOP -40 to 85 |
| LTC2414 | 2-Channel Differential Input 24-Bit No Latency DS ADC |
| LTC2418 | Replaced by SN74ALVCH16374 : 16-Bit Edge-Triggered D-Type Flip-Flop With 3-State Outputs 48-SSOP -40 to 85 |
| LTC2412IGN | 2-Channel Differential Input 24-Bit No Latency DS ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2411-1CMS | 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2411-1CMS#PBF | 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2411-1CMS#TR | 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2411-1CMS#TRPBF | 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2411-1CMSPBF | 制造商:Linear Technology 功能描述:ADC 24-Bit Differential and Ref. MSOP10 |
發布緊急采購，3分鐘左右您將得到回復。