- 您現在的位置：買賣IC網 > PDF目錄377769 > LTC2412 (Linear Technology Corporation) 16-Bit Universal Bus Driver With 3-State Outputs 48-SSOP -40 to 85 PDF資料下載
參數資料
| 型號： | LTC2412 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 16-Bit Universal Bus Driver With 3-State Outputs 48-SSOP -40 to 85 |
| 中文描述： | 2路差分輸入24位ADC的無延遲局副局長 |
| 文件頁數： | 14/36頁 |
| 文件大?。?/td> | 409K |
| 代理商： | LTC2412 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC2412
14
2412f
Bit 31 (first output bit) is the end of conversion (EOC)
indicator. This bit is available at the SDO pin during the
conversion and sleep states whenever the CS pin is LOW.
This bit is HIGH during the conversion and goes LOW
when the conversion is complete.
Bit 30 (second output bit) is the selected channel indicator.
The bit is LOW for channel 0 and HIGH for channel 1
selected.
Bit 29 (third output bit) is the conversion result sign indi-
cator (SIG). If V
IN
is >0, this bit is HIGH. If V
IN
is <0, this
bit is LOW.
Bit 28 (fourth output bit) is the most significant bit (MSB)
of the result. This bit in conjunction with Bit 29 also
provides the underrange or overrange indication. If both
Bit 29 and Bit 28 are HIGH, the differential input voltage is
above +FS. If both Bit 29 and Bit 28 are LOW, the
differential input voltage is below –FS.
The function of these bits is summarized in Table 1.
Table 1. LTC2412 Status Bits
Bit 31
EOC
0
0
0
0
Bit 30
CH0/CH1
0 or 1
0 or 1
0 or 1
0 or 1
Bit 29 Bit 28
SIG
1
1
0
0
Input Range
V
IN
≥
0.5 V
REF
0V
≤
V
IN
< 0.5 V
REF
–0.5 V
REF
≤
V
IN
< 0V
V
IN
< –0.5 V
REF
MSB
1
0
1
0
Bits 28-5 are the 24-bit conversion result MSB first.
Bit 5 is the least significant bit (LSB).
Bits 4-0 are sub LSBs below the 24-bit level. Bits 4-0 may
be included in averaging or discarded without loss of
resolution.
Data is shifted out of the SDO pin under control of the serial
clock (SCK), see Figure 3. Whenever CS is HIGH, SDO
remains high impedance and any externally generated
SCK clock pulses are ignored by the internal data out shift
register.
In order to shift the conversion result out of the device, CS
must first be driven LOW. EOC is seen at the SDO pin of the
device once CS is pulled LOW. EOC changes real time from
HIGH to LOW at the completion of a conversion. This
signal may be used as an interrupt for an external micro-
controller. Bit 31 (EOC) can be captured on the first rising
edge of SCK. Bit 30 is shifted out of the device on the first
falling edge of SCK. The final data bit (Bit 0) is shifted out
on the falling edge of the 31st SCK and may be latched on
the rising edge of the 32nd SCK pulse. On the falling edge
of the 32nd SCK pulse, SDO goes HIGH indicating the
initiation of a new conversion cycle. This bit serves as EOC
(Bit 31) for the next conversion cycle. Table 2 summarizes
the output data format.
As long as the voltage on the analog input pins is main-
tained within the –0.3V to (V
CC
+ 0.3V) absolute maximum
operating range, a conversion result is generated for any
differential input voltage V
IN
from –FS = –0.5 V
REF
to
+FS = 0.5 V
REF
. For differential input voltages greater than
+FS, the conversion result is clamped to the value corre-
sponding to the +FS + 1LSB. For differential input voltages
below –FS, the conversion result is clamped to the value
corresponding to –FS – 1LSB.
APPLICATIU
W
U
U
Figure 3. Output Data Timing
MSB
SIG
CH0/CH1
1
2
3
4
5
26
27
32
BIT 0
BIT 27
BIT 5
LSB
24
BIT 28
BIT 29
BIT 30
SDO
SCK
CS
EOC
BIT 31
SLEEP
DATA OUTPUT
CONVERSION
2412 F03
Hi-Z
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2412CGN | 16-Bit Universal Bus Driver With 3-State Outputs 48-TVSOP -40 to 85 |
| LTC2414 | 2-Channel Differential Input 24-Bit No Latency DS ADC |
| LTC2418 | Replaced by SN74ALVCH16374 : 16-Bit Edge-Triggered D-Type Flip-Flop With 3-State Outputs 48-SSOP -40 to 85 |
| LTC2412IGN | 2-Channel Differential Input 24-Bit No Latency DS ADC |
| LTC2420CS8 | 20-Bit uPower No Latency ADC in SO-8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2412CGN | 功能描述:IC ADC 2CH DIFF-IN 24BIT 16SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2412CGN#PBF | 功能描述:IC ADC 2CH DIFF-IN 24BIT 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2412CGN#PBF | 制造商:Linear Technology 功能描述:IC, ADC, 24BIT, SSOP-16 |
| LTC2412CGN#TR | 功能描述:IC CONV A/D 24B 2CH DIFF 16-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2412CGN#TRPBF | 功能描述:IC ADC 2CH DIFF-IN 24BIT 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。