- 您現在的位置：買賣IC網 > PDF目錄377770 > LTC2420 (Linear Technology Corporation) Micropower 20-bit ADC(微功耗，20位串行模數轉換器) PDF資料下載
參數資料
| 型號： | LTC2420 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Micropower 20-bit ADC(微功耗，20位串行模數轉換器) |
| 中文描述： | 微功耗20位ADC（微功耗，20位串行模數轉換器） |
| 文件頁數： | 22/36頁 |
| 文件大?。?/td> | 388K |
| 代理商： | LTC2420 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
22
LTC2420
APPLICATIU
W
U
U
The internal serial clock mode is selected every time the
voltage on the CS pin crosses an internal threshold volt-
age. An internal weak pull-up at the SCK pin is active while
CS is discharging; therefore, the internal serial clock
timing mode is automatically selected if SCK is floating. It
is important to ensure there are no external drivers pulling
SCK LOW while CS is discharging.
DIGITAL SIGNAL LEVELS
The LTC2420’s digital interface is easy to use. Its digital
inputs (F
O
, CS and SCK in External SCK mode of operation)
accept standard TTL/CMOS logic levels and the internal
hysteresis receivers can tolerate edge rates as slow as
100
μ
s. However, some considerations are required to take
advantage of exceptional accuracy and low supply current.
CAPACITANCE ON CS (pF)
0
S
3
4
5
1000
100000
2420 F14
2
1
0
10
100
10000
6
7
8
V
CC
= 5V
V
CC
= 3V
Figure 14. CS Capacitance vs Output Rate
CAPACITANCE ON CS (pF)
1
0
S
μ
A
R
)
50
100
150
200
250
300
10
100
1000
10000
2420 F15
100000
V
CC
= 5V
V
CC
= 3V
Figure 15. CS Capacitance vs Supply Current
The digital output signals (SDO and SCK in Internal SCK
mode of operation) are less of a concern because they are
not generally active during the conversion state.
In order to preserve the LTC2420’s accuracy, it is very
important to minimize the ground path impedance which
may appear in series with the input and/or reference signal
and to reduce the current which may flow through this path.
The GND pin should be connected to a low resistance
ground plane through a minimum length trace. The use of
multiple via holes is recommended to further reduce the
connection resistance. The LTC2420’s power supply cur-
rent flowing through the 0.01
resistance of the common
ground pin will develop a 2.5
μ
V offset signal. For a refer-
ence voltage V
REF
= 2.5V, this represents a 1ppm offset
error.
In an alternative configuration, the GND pin of the converter
can be the single-point-ground in a single point grounding
system. The input signal ground, the reference signal
ground, the digital drivers ground (usually the digital
ground) and the power supply ground (the analog ground)
should be connected in a star configuration with the com-
mon point located as close to the GND pin as possible.
The power supply current during the conversion state
should be kept to a minimum. This is achieved by restrict-
ing the number of digital signal transitions occurring
during this period.
While a digital input signal is in the range 0.5V to
(V
CC
–0.5V), the CMOS input receiver draws additional
current from the power supply. It should be noted that,
when any one of the digital input signals (F
O
, CS and SCK
in External SCK mode of operation) is within this range, the
LTC2420 power supply current may increase even if the
signal in question is at a valid logic level. For micropower
operation and in order to minimize the potential errors due
to additional ground pin current, it is recommended to
drive all digital input signals to full CMOS levels
[V
IL
< 0.4V and V
OH
> (V
CC
– 0.4V)].
Severe ground pin current disturbances can also occur
due to the undershoot of fast digital input signals. Under-
shoot and overshoot can occur because of the imped-
ance mismatch at the converter pin when the transition
time of an external control signal is less than twice the
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2435IGN | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
| LTC2435-1IGN | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
| LTC2435 | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
| LTC2435-1 | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
| LTC2435-1CGN | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2420CS8 | 功能描述:IC ADC 20BIT MICRPWR W/OSC 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2420CS8#PBF | 功能描述:IC ADC 20BIT MICRPWR W/OSC 8SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2420CS8#PBF | 制造商:Linear Technology 功能描述:A/D Converter (A-D) IC |
| LTC2420CS8#TR | 功能描述:IC A/D CONV 20BIT MICRPWR 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2420CS8#TRPBF | 功能描述:IC ADC 20BIT MICRPWR W/OSC 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。