參數資料
型號： LTC2435
廠商： Linear Technology Corporation
英文描述： 20-Bit No Latency ADCs with Differential Input and Differential Reference
中文描述： 20位無與差分輸入和差分ADC的參考延遲
文件頁數： 10/40頁
文件大?。?/td> 463K
代理商： LTC2435
LTC2435/LTC2435-1
10
24351fa
GND (Pins 1, 7, 8, 9, 10, 15, 16):
Ground. Multiple ground
pins internally connected for optimum ground current flow
and V
CC
decoupling. Connect each one of these pins to a
ground plane through a low impedance connection. All seven
pins must be connected to ground for proper operation.
V
CC
(Pin 2):
Positive Supply Voltage. Bypass to GND
(Pin 1) with a 10
μ
F tantalum capacitor in parallel with
0.1
μ
F ceramic capacitor as close to the part as possible.
REF
+
(Pin 3), REF
–
(Pin 4):
Differential Reference Input.
The voltage on these pins can have any value between GND
and V
CC
as long as the reference positive input, REF
+
, is
maintained more positive than the reference negative
input, REF
–
, by at least 0.1V.
IN
+
(Pin 5), IN
–
(Pin 6):
Differential Analog Input. The
voltage on these pins can have any value between
GND – 0.3V and V
CC
+ 0.3V. Within these limits the
converter bipolar input range (V
IN
= IN
+
– IN
–
) extends
from –0.5 (V
REF
) to 0.5 (V
REF
). Outside this input range
the converter produces unique overrange and underrange
output codes.
CS (Pin 11):
Active LOW Digital Input. A LOW on this pin
enables the SDO digital output and wakes up the ADC.
Following each conversion, the ADC automatically enters
the Sleep mode and remains in this low power state as
long as CS is HIGH. A LOW-to-HIGH transition on CS
during the Data Output transfer aborts the data transfer
and starts a new conversion.
SDO (Pin 12):
Three-State Digital Output. During the Data
Output period, this pin is used as serial data output. When
the chip select CS is HIGH (CS = V
CC
) the SDO pin is in a
high impedance state. During the Conversion and Sleep
periods, this pin is used as the conversion status output.
The conversion status can be observed by pulling CS LOW.
SCK (Pin 13):
Bidirectional Digital Clock Pin. In Internal
Serial Clock Operation mode, SCK is used as digital output
for the internal serial interface clock during the Data
Output period. In External Serial Clock Operation mode,
SCK is used as digital input for the external serial interface
clock during the Data Output period. A weak internal pull-
up is automatically activated in Internal Serial Clock Op-
eration mode. The Serial Clock Operation mode is deter-
mined by the logic level applied to the SCK pin at power up
or during the most recent falling edge of CS.
F
O
(Pin 14):
Frequency Control Pin. Digital input that
controls the ADC’s notch frequencies and conversion
time. When the F
O
pin is connected to V
CC
(LTC2435 only),
the converter uses its internal oscillator and the digital
filter first null is located at 50Hz. When the F
O
pin is
connected to GND (F
O
= OV), the converter uses its internal
oscillator and the digital filter first null is located at 60Hz
(LTC2435) or simultaneous 50Hz/60Hz (LTC2435-1).
When F
O
is driven by an external clock signal with a
frequency f
EOSC
, the converter uses this signal as its
system clock and the digital filter first null is located at a
frequency f
EOSC
/2560.
PIU
相關PDF資料
PDF描述
LTC2435-1 20-Bit No Latency ADCs with Differential Input and Differential Reference
LTC2435-1CGN 20-Bit No Latency ADCs with Differential Input and Differential Reference
LTC2435CGN 20-Bit No Latency ADCs with Differential Input and Differential Reference
LTC2436-1IGN 2-Channel Differential Input 16-Bit No Latency DS ADC
LTC2436-1 2-Channel Differential Input 16-Bit No Latency DS ADC
相關代理商/技術參數
參數描述
LTC2435-1CGN 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
LTC2435-1CGN#PBF 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2435-1CGN#TR 功能描述:IC CONV A/D 20BIT DIFF 16-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
LTC2435-1CGN#TRPBF 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
LTC2435-1IGN 功能描述:IC CONV A/D 20BIT DIFF 16-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*