- 您現在的位置：買賣IC網 > PDF目錄377770 > LTC2480CDD (LINEAR TECHNOLOGY CORP) 16-Bit ADC with Easy Drive PDF資料下載
參數資料
| 型號： | LTC2480CDD |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 16-Bit ADC with Easy Drive |
| 中文描述： | 1-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO10 |
| 封裝： | 3 X 3 MM, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件頁數： | 19/40頁 |
| 文件大小： | 535K |
| 代理商： | LTC2480CDD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
19
LTC2480
2480f
When using the internal temperature sensor, if the output
code is normalized to R
SDO
= V
PTAT
/V
REF
, the temperature
is calculated using the following formula:
T
R
V
SLOPE
T
R
V
SLOPE
K
SDO
REF
C
SDO
REF
=
=
–
in Kelvin
and
in C
273
where SLOPE is nominally 1.4mV/
°
C.
Since the PTAT signal can have an initial value variation
which results in errors in SLOPE, to achieve better tem-
perature measurements, a one-time calibration is needed
to adjust the SLOPE value. The converter output of the
PTAT signal, R0
SDO
, is measured at a known temperature
T0 (in
°
C) and the SLOPE is calculated as:
SLOPE
R
V
T
SDO
0
REF
=
+
0
273
This calibrated SLOPE can be used to calculate the
temperature.
If the same V
REF
source is used during calibration and
temperature measurement, the actual value of the V
REF
is
not needed to measure the temperature as shown in the
calculation below:
T
R
V
SLOPE
SDO
SDO
0
R
R
T
C
SDO
REF
=
=
+
(
)
–
–
273
0
273
273
Reference Voltage Range
The LTC2480 external reference voltage range is 0.1V to
V
CC
. The converter output noise is determined by the
thermal noise of the front-end circuits, and as such, its
value in nanovolts is nearly constant with reference volt-
age. Since the transition noise (600nV) is much less than
the quantization noise (V
REF
/2
17
), a decrease in the refer-
ence voltage will increase the converter resolution. A
reduced reference voltage will also improve the converter
performance when operated with an external conversion
clock (external F
O
signal) at substantially higher output
data rates (see the Output Data Rate section). V
REF
must
be
≥
1.1V to use the internal temperature sensor.
The negative reference input to the converter is internally
tied to GND. GND (Pin 8) should be connected to a ground
plane through as short a trace as possible to minimize
voltage drop. The LTC2480 has an average operational
current of 160
μ
A and for 0.1
parasitic resistance, the
voltage drop of 16
μ
V causes a gain error of 3.2ppm for
V
REF
= 5V.
Input Voltage Range
The analog input is truly differential with an absolute/
common mode range for the IN
+
and IN
–
input pins
extending from GND – 0.3V to V
CC
+ 0.3V. Outside
these limits, the ESD protection devices begin to turn on
and the errors due to input leakage current increase
rapidly. Within these limits, the LTC2480 converts the
bipolar differential input signal, V
IN
= IN
+
– IN
–
, from –FS
to +FS where FS = 0.5 V
REF
/GAIN. Outside this range, the
converter indicates the overrange or the underrange con-
dition using distinct output codes. Since the differential
input current cancellation does not rely on an on-chip
buffer, current cancellation as well as DC performance is
maintained rail-to-rail.
I
nput signals applied to IN
+
and IN
–
pins may extend by
300mV below ground and above V
CC
. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN
+
and IN
–
pins without affecting the perfor-
mance of the devices. The effect of the series resistance
on the converter accuracy can be evaluated from the
curves presented in the Input Current/Reference Current
sections. In addition, series resistors will introduce a
APPLICATIU
W
U
U
Figure 4. Internal PTAT Signal vs Temperature
TEMPERATURE (
°
C)
–60
V
P
500
600
120
2480 F04
400
200
30
0
90
–30
60
300
V
= 5V
IM = 1
F
= GND
SLOPE = 1.40mV/
°
C
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2486 | 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation |
| LTC2486CDE | 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation |
| LTC2486IDE | 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation |
| LTC2487 | 16-Bit 2-/4-Channel ADC with PGA, Easy Drive and I2C Interface |
| LTC2487CDEPBF | 16-Bit 2-/4-Channel ADC with PGA, Easy Drive and I2C Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2480CDD#PBF | 功能描述:IC ADC 16BIT 10-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2480CDD#TR | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 7.5sps 16-bit Serial 10-Pin DFN EP T/R |
| LTC2480CDD#TRPBF | 功能描述:IC ADC 16BIT 10-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2480CDDPBF | 制造商:Linear Technology 功能描述:16-Bit ADC Easy Drive Current Canc.DFN10 |
| LTC2480CMS#PBF | 功能描述:IC ADC 16BIT 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。